This specification covers 6101 aluminum-alloy extruded bar, rod, tube, pipe, (Schedules 40 and 80), structural profiles, and profiles in selected tempers for use as electric conductors. The bars, rods, tubes, pipes, structural profiles and profiles shall be produced by hot extrusion or by similar methods. Pipe or tube may be produced through porthole or bridge type dies. Tensile properties of the specimens such as tensile and yield strengths and bending shall be determined by tension test and bending test, respectively. Electrical resistivity and conductivity shall be determined.1.1 This specification covers 6101 aluminum-alloy extruded bar, rod, tube, pipe, (Schedules 40 and 80), structural profiles, and profiles in selected tempers for use as electric conductors as follows:1.1.1 Type B—Hot-finished bar, rod, tube, pipe, structural profiles and profiles in T6, T61, T63, T64, T65, and H111 tempers with Type B tolerances, as shown in the “List of ANSI Tables of Dimensional Tolerances.”1.1.2 Type C—Hot-finished rectangular bar in T6, T61, T63, T64, T65, and H111 tempers with Type C tolerances as listed in the tolerances and permissible variations tables.1.2 Alloy and temper designations are in accordance with ANSI H35.1. The equivalent Unified Numbering System alloy designation in accordance with Practice E527 is A96101 for Alloy 6101.NOTE 1: Type A material, last covered in the 1966 issue of this specification, is no longer available; therefore, requirements for cold-finished rectangular bar have been deleted.1.3 The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

2.1 This practice is applicable to distinguish between properly and improperly extruded PVC plastic pipe. It can be used to:2.1.1 Reveal incomplete exsiccation of compound before or during extrusion (Note 1),2.1.2 Determine the presence of stress in the pipe wall produced by the extrusion process (Note 2),2.1.3 Determine whether unfused areas are present, and2.1.4 Reveal contamination.NOTE 1: Residual moisture in the compound vaporizes at extrusion temperatures and is normally evacuated as it forms vapor. Pockets of moisture trapped in the pipe wall result from incomplete exsiccation of the compound, and may reduce the physical properties of the pipe.NOTE 2: Minor residual stress in the pipe will not impair field performance and handleability. High-residual stress has no proven effect on performance, but may impair handleability during installation.1.1 This practice covers a procedure for estimating the quality of extruded poly (vinyl chloride) (PVC) plastic pipes by observing the reaction of pipe specimens after exposure to hot air in the oven at 180 °C ± 5 °C (356 °F  ± 9 °F) for 30 minutes minimum time duration.1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded and compression molded plate, rod and tubular bar manufactured from thermoplastic polyester. Each type of thermoplastic polyester shape may be categorized into one of several grades as follows: grade 1 - general purpose-extruded or compression molded product made using only 100 % virgin thermoplastic polyester resin and grade 2 - recycled-extruded or compression molded product made using any amount up to 100 % recycled thermoplastic polyester plastics. Tensile stress break, elongation at break, and tensile modulus shall be tested to meet the requirements prescribed.1.1 This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded and compression molded plate, rod and tubular bar manufactured from thermoplastic polyester.1.2 The properties included in this specification are those required for the compositions covered. Use the classification system given in Section 4 to describe requirements necessary to identify particular characteristics important to specialized applications.1.3 This specification allows the use of recycled plastics2 (see Section 4).1.4 The values are stated in inch-pound units and are regarded as the standard in all property and dimensional tables. For reference purposes, SI units are also included in Table 1 and Table S-TPES only.1.5 The following precautionary caveat pertains only to the test method portions sections of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: There is no known ISO equivalent to this standard.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers requirements and methods of test for the material, dimensions, and workmanship, and the properties of extruded, compression molded, and injection molded PAEK sheet, plate, rod, and tubular bar manufactured from PAEK. The type of PAEK extruded, compression molded, and injection molded product may be categorized by type, grade and class depending on resin and filler compositions. Every type of PAEK shape may be categorized into one of several grades as follows: Grade 1 (general purpose) which is extruded, compression molded or injection molded product made using only 100% virgin PAEK resin and Grade 2 (recycle grade) which is extruded, compression molded or injection molded product made using any amount up to 100% of recycled thermoplastic PAEK. The type, class and grade is further differentiated based on dimensional stability. Different tests shall be conducted in order to determine the following properties of PAEK: tensile stress at break, elongation at break, tensile modulus, dimensional stability, lengthwise camber and widthwise bow, squareness, flexural modulus, and Izod impact.1.1 This specification covers requirements for the PAEK materials used and the requirements and methods of test for the dimensions, workmanship, and the properties of extruded, compression molded, and injection molded PAEK sheet, plate, rod, and tubular bar manufactured from PAEK. PAEK is a family of thermoplastic materials that differ in properties (see Section 3).1.2 The properties included in this specification are those required for the compositions covered. Requirements necessary to identify particular characteristics important to specialized applications are described by using the classification system given in Section 4.1.3 This specification allows the use of key clad plastics (see Section 4).1.4 The values are stated in inch-pound units and are regarded as the standard in all property and dimensional tables. For reference purposes, SI units are also included in Table 1.1.5 The following precautionary caveat pertains only to the test method portion Section 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: There is no known ISO equivalent to this standard.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers the requirements and test methods for the material, dimensions, and workmanship of extruded, compression molded, and injection molded basic shapes. The specimens shall be made of polyamide-imide which may be filled, lubricated, or reinforced with carbon, graphite, or glass fibers; lubricants such as PTFE, graphite, silicone, and molybdenum disulfide; mineral; combinations of reinforcements or fillers; or both. Tests shall be conducted in the standard laboratory conditions to determine the physical properties of the specimens. Physical properties shall conform to the ultimate tensile strength, elongation at break, tensile modulus, flexural modulus, Izod impact, glass transition temperature, and specific gravity requirements. Dimensional tests shall also be performed to determine the conformance of the specimens to the size thickness, thickness tolerance, camber length, and width bow specifications.1.1 This specification covers requirements and methods of test for the material, dimensions, and workmanship of extruded, compression molded, and injection molded parts manufactured from PAI.1.2 The properties included in this specification are those required for the compositions covered. Requirements necessary to identify particular characteristics important to specialized applications are described by the classification system given in Section 5.1.3 This specification allows for the use of recycled materials provided that specification requirements based upon this specification are met.1.4 The values stated in English units are to be regarded as standard in all property and dimensional tables. For reference purposes, SI units and conversion factors are also included.1.5 The following precautionary caveat pertains only to the test method portion Section 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: There is no known ISO equivalent to this standard.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This test method covers requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded and compression-molded sheet, plate, rod and tubular bar manufactured from polyetherimide (PEI) resins. The type of PEI extruded shape shall be categorized by class depending on composition. Every class of PEI shape shall be categorized into one grade for virgin unfilled products. The type and class shall be further differentiated based on dimensional tolerances and dimensional stability (based on elevated temperature excursion testing). Grades 1 and 2 materials are produced with the closest commercial tolerances and lowest stress levels for machined parts. The type, class, and grade is further differentiated based on dimensional stability (elevated temperature excursion test). Tensile strength at break, elongation at break, flexural modulus, izod impact, and tensile modulus (tangent) shall be tested to meet the requirements prescribed. The plate specimens, sheet specimens, rod specimens, and tubular bar specimens shall be tested to meet the requirements prescribed.1.1 This specification covers requirements and test methods for the dimensions, workmanship, and the properties of extruded and compression-molded sheet, plate, rod and tubular bar manufactured from polyetherimide (PEI) resins.1.2 The properties included in this specification are those required for the compositions covered. It is possible that other requirements will be necessary to identify particular characteristics important to specialized applications. These shall be specified by using the suffixes as given in Section 5.1.3 This specification does not allow for the use of recycled plastics (as defined in Guide D7209).1.4 The values stated in English units are regarded as standard in all property and dimensional tables. For reference purposes, SI units are also included in Table 1 and Table S-PEI.1.5 The following safety hazards caveat pertains only to the test method or test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: There is no known ISO equivalent to this standard.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers extruded and cast sheet, plate, rod and tubular bar manufactured from nylon or monomers. Requirements necessary to identify particular characteristics important to specialized applications may be described by using the given classification system. The use of recycled plastics is allowed in the specification. The materials shall be subject to tests to determine tensile strength at break, tensile modulus, dimensional stability, lengthwise camber and widthwise bow, squareness, flexural modulus, and Izod impact.1.1 This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded and cast sheet, plate, rod and tubular bar, excluding pipe and fittings, manufactured from nylon or monomers.1.2 The properties included in this specification are those required for the compositions covered. Requirements necessary to identify particular characteristics important to specialized applications are described by using the classification system given in Section 4.1.3 This specification allows for the use of recycled plastics (as defined in Guide D7209).1.4 The values stated in English units are regarded as standard. The values in parentheses are for information only.1.5 The following precautionary caveat pertains only to the test method portions of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: There is no known ISO equivalent to this standard.NOTE 2: This specification is intended to replace Federal Standard LP-410A and PS 50.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded shapes of rods and bars made from poly(vinyl chloride) (PVC), and chlorinated poly(vinyl chloride) (CPVC). The type of poly(vinyl chloride), and chlorinated poly(vinyl chloride) shape product may be categorized by type, grade, and class depending on resin composition: Types 01 and 02; Classes 0 and 1; Grades 0 and 1. The type, class and grade is further differentiated based on dimensional stability. The following test methods shall be performed: tensile stress at break; elongation at break; tensile modulus; dimensional stability; lengthwise chamber; flexural modulus; izod impact; and degree of fusion of extruded PVC and CPVC by solvent immersion.1.1 This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded shapes of rods and bars made from poly(vinyl chloride) (PVC), and chlorinated poly(vinyl chloride) (CPVC).1.2 The properties included in this specification are those required for the compositions covered. Use the classification system given in Section 4 to describe requirements necessary to identify particular characteristics important to specialized applications.1.3 This specification allows for the use of regrind and recycled plastics providing products produced from regrind or recycled PVC material can be shown to meet the requirements of this standard with regard to material classification, physical performance, dimensions and workmanship; and the regrind or recycled plastics used have not been subjected to severe environments in post consumer applications (such as chemical service) which could adversely affect the end products performance when subjected to machining or critical applications or both.1.4 The values are stated in inch-pound units and are regarded as the standard in all property and dimensional tables. For reference purposes, SI units are also included in Table 1 only.1.5 The following safety hazards caveat pertains only to the test method portions section of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: There is no known ISO equivalent to this standard.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers the testing and requirements of extruded and compression molded polytetrafluoroethylene (PTFE) rods and heavy-walled tubing manufactured from virgin or reprocessed PTFE resin. Covered here are three types of PTFE fluorocarbon materials as follows: Type I (premium), materials having maximum physical and electrical properties to meet rigid requirements; Type II (general purpose), materials having properties required of general electrical, mechanical, and chemical applications; and Type III, materials for noncritical chemical, electrical, and mechanical applications. These types are further subdivided into two grades, and even further into four classes as appropriate. Sampled specimens shall be appropriately tested on the following: workmanship and appearance (color, finish, and internal defects); specific gravity; tensile strength and elongation; dielectric strength; dimensional stability; and melting point.1.1 This specification covers extruded polytetrafluoroethylene (PTFE) rod, heavy-walled tubing, and basic shapes manufactured from the PTFE resin of Specification D4894 and reprocessed PTFE resin (as defined in Guide D7209).1.2 The specification covers all sizes of rod, tubing, and basic shapes with a wall thickness of 1.6 mm (1/16 in.) or greater. These materials must be made wholly from PTFE and produced in accordance with good commercial ram extrusion practices.NOTE 1: This specification and ISO/DIS 13000-1 (1997) and ISO/DIS 13000-2 (1997) differ in approach, however, data obtained using either are technically equivalent.NOTE 2: For compression molded PTFE materials, see Specification D3294. Material that can be certified to Specification D3294 may be substituted for Specification D1710, however the reverse in not true.1.3 The values stated in SI units, as detailed in IEEE/ASTM SI 10 are to be regarded as the standard. The inch-pound units given in parentheses are provided for information only.1.4 The following precautionary caveat pertains to the test methods portion, Section 12, only of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

3.1 This test method is applicable only for distinguishing between inadequately fused and adequately fused PVC. The difference between thermally degraded and adequately fused PVC cannot be detected by this test method. Acetone immersion testing is not a substitute for burst, impact, or other physical or chemical tests on PVC pipe or fittings and it, therefore, shall not be used as the only test specification for purchasing of PVC pipe and fittings. This test method only detects inadequate fusion and does not determine the over-all quality of the PVC pipe or fittings.3.2 This test method is useful in determining whether inadequate fusion contributed to failure of PVC pipe or fittings in other physical or chemical tests, or in service.3.3 This test method is useful in evaluating the adequacy of PVC fusion obtained in process or materials trials.3.4 This test method determines adequacy of fusion on a single, relatively small specimen. This test method requires the use of a hazardous reagent which must be properly handled and disposed. Therefore, this test method may not be cost-effective to employ as a routine quality control test.1.1 This test method covers the determination of the adequacy of fusion of extruded rigid poly(vinyl chloride) (PVC) pipe and molded fittings as indicated by reaction to immersion in anhydrous acetone.1.2 The values stated in inch-pound units are to be regarded as the standard except where instruments are calibrated in SI units.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.Specific hazards statements are given in Annex A1.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 This test method will provide differentiation between types of coatings for acid and motor resistance providing the coating is applied in a uniform continuous film with a specified film thickness.1.1 This test method covers the evaluation of the mortar and acid resistance of clear protective coating factory applied to extruded aluminum substrates.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers four types of polychlorotrifluoroethylene extruded plastic sheet and film: Type I - a transparent film with high and low moisture vapor transmission rate; Type II - a dimensionally stable transparent sheet and film with low moisture vapor transmission rate; Type III - a dimensionally stable transparent film with very low moisture vapor transmission rate; and Type IV - a low crystalline transparent film with high ductility and extremely low moisture vapor transmission rate. The specimens shall be manufactured from polychlorotrifluoroethylene plastics that consist of at least 90% chlorotrifluoethylene and 10% chemical modification such as co-monomers but not colorants, fillers, plasticizers, or mechanical blends of other resins. Tests shall be conducted to determine the specific property values of the specimen which shall conform to the tensile strength, elongation, dimensional stability or shrinkage, and moisture vapor transmission rate requirements.1.1 This specification covers extruded sheet and film in thicknesses from 0.015 to 0.25 mm (0.0006 to 0.01 in.).1.2 The values stated in SI units shall be regarded as the standard.1.3 The following precautionary statement pertains only to the test methods portion, Section 9 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: There is no known ISO equivalent to this standard.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This guide identifies the standard test methods to use in evaluating unsintered extruded films or tapes manufactured from polytetrafluoroethylene (PTFE). The test methods covered here shall be capable of investigating the following material properties: width; thickness; tensile properties (tensile strength and elongation); specificat gravity (relative density); residual extrusion aids or other volatile components; dielectric constant; volume resistivity; dielectric breakdown voltage; and unit weight.1.1 This guide identifies test methods to use in evaluating unsintered extruded films or tapes manufactured from polytetrafluoroethylene.1.2 The values stated in SI units as detailed in IEEE/ASTM SI 10, are to be regarded as standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: This test method is equivalent to ISO 12086-2:2006 in the measurement of tensile properties, specific gravity, and dielectric constant. These are in ISO 12086-2:2006, sections 8.2.2, 10.6 and 8.1.1. It is not equivalent to ISO 12086-2:2006 in any other measurement or section..1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

Preface This is the common CSA and UL standard for Extruded Insulating Tubing. It is the third edition of CSA C22.2 No. 198.1 and the sixth edition of UL 224. This edition of CSA C22.2 No. 198.1 supersedes the previous edition published in 1999.

定价： 3504元 / 折扣价： 2979 元

This specification covers the pipe materials and dimensions for producing non-reinforced extruded tee connections manufactured by mechanical forming processes. The term “extruded tee connection” applies to butt-weld or socket-weld connections. The non-reinforced extruded pipe tee connection is an alternative to the tee fittings, nozzle, and other welded connections. The non-reinforced extruded pipe tee connection has been widely used for systems in the marine, process piping, food, pharmaceutical, and similar industries. Different materials that have acceptable forming qualities to produce extruded tee connections shall consist of copper, copper-nickel alloy, titanium, steel, and stainless steel. The extruded tee connection shall be free from burrs and cracks, which would affect the suitability for the intended service.1.1 This specification covers the pipe materials and dimensions for producing non-reinforced extruded tee connections manufactured by mechanical forming processes. The term “extruded tee connection” applies to butt-weld or socket-weld connections. This specification refers to the forming process that leads to welding or brazing.1.2 The non-reinforced extruded pipe tee connection is an alternative to the tee fittings, nozzle, and other welded connections.1.3 The non-reinforced extruded pipe tee connection has been widely used for systems in the marine, process piping, food, pharmaceutical, and similar industries.1.4 The extruded tee connection will be welded in accordance with Specification F722. Brazing of tee connections will be in accordance with ASME B31.5.1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车