4.1 This guide is intended to provide designers, specifiers, owners, operators and managers of synthetic turf playing systems with information related to specifying, measuring and managing impact attenuation.4.2 The goal of this guide is to facilitate decisions and actions that will maximize the safety, playability and functional longevity of individual synthetic turf playing systems, primarily as related to impact attenuation.4.3 This guide presents various options related to specifying, measuring and managing impact attenuation of synthetic turf playing systems.4.4 Unless specifically stated, this guide does not attempt to endorse or recommend specific options or practices. It is left to the user of the guide to determine the option, practice or course of action that is most appropriate for them, given the specifics of their individual situation.1.1 Applicable to synthetic turf playing systems, regardless of intended use, which are subject to testing in accordance with Specification F1936.1.2 Applicable to synthetic turf playing systems installed either indoors or outdoors.1.3 Not applicable to natural turf playing systems.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 Data obtained from the procedure of this test method are indicative of the relative abrasiveness of fabric or carpet type synthetic playing surfaces.1.1 This test method is applicable to both laboratory and field measurement of synthetic turf surfaces used for sports.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 This test method is to be used to measure the impact attenuation of synthetic turf rugby fields and to estimate the CFH performance.5.2 It is acceptable for this test method to be specified for use by other organizations, specifiers, or facility owners where it is deemed appropriate.1.1 This standard establishes a test method to be used when testing a synthetic turf field’s impact attenuation property for assessing its suitability for rugby.1.2 The surface being tested will be located indoors or outdoors and typically includes the entire surface, both within the boundary lines of the playing area and outside of it. Where non-turf surfaces exist within these areas, they shall be excluded from the scope of this standard, unless they are covered either permanently or temporarily with synthetic turf.1.3 It is acceptable to use this test method, where appropriate, as a test method for laboratory based testing of synthetic turf surfaces.1.4 The definition of a minimum performance requirement for this test method is outside of the scope of this standard. Where reference is made to a minimum requirement this is intended for demonstration and clarification purposes only.1.5 This test method establishes a method of reporting test results.1.6 The values stated in SI units are to be regarded as standard. Where values are given in parenthesis they are mathematical conversions to inch-pound units that are provided for information purposes only and are not considered standard.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers a test method and the corresponding performance requirement for the maximum impact attenuation in all types of turf playing systems installed for North American football fields that is intended to establish a method for identifying and reporting areas within an existing playing system where shock-absorbing properties exceed recommended threshold values. The turf playing system typically includes field areas within and outside the inbound lines extending to the sport specific limit lines as defined by the appropriate regulating body or appropriate standard, or both. All of these areas are regions where an athlete should expect compliant impact attenuation characteristics, but, it does not imply that an injury cannot be incurred if the surface system complies with this specification. The test method, aptly called the free-fall drop test, shall be performed at eight different test point locations for four specific types of surface systems, namely: synthetic turf systems with resilient padding; natural turf systems; combination turf systems; and infill synthetic turf systems.1.1 This specification establishes an in situ test method and maximum impact attenuation value for all types of turf playing systems and for a number of sport-specific field layouts. It also includes a protocol for determining test point locations on fields that are lined for multiple sports.1.1.1 Turf playing systems may be located outdoors or indoors, and typically include field areas within the in-bounds lines and areas outside the in-bounds lines extending to sport-specific limit lines; areas where an athlete should expect to encounter impact attenuation performance that complies with this specification.1.1.2 Site-specific conditions may exist wherein non-turf surface materials, such as track surfacing and/or covers over subsurface structures, are found within the boundaries of the limit lines. These alternate surface materials are not included in the scope of this specification.1.2 This specification establishes a method for reporting test results and identifying areas within an existing turf playing system where impact attenuation measurements exceed required threshold values.1.3 Nothing in this specification is intended to impose limitations on what fields can be tested, or how a particular field can be used. Test providers can adapt the procedures and guidelines contained herein to tests performed on any turf playing system.1.4 This specification does not imply that an impact-related injury cannot be incurred if a turf playing system complies with its g-max performance requirement.1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

5.1 Resiliency may be used to control the quality of many TRMs. Resiliency may be indicative of a TRM's ability to retain original configuration after exposure to the stresses which may be exerted during manufacture, shipping, and installation. Resiliency is not generally indicative of field performance.5.2 The resiliency of TRMs may vary considerably depending on the pressure applied to the specimen during loading cycles. To minimize variation, specific sample size and applied pressure are indicated in this test method to ensure all results are comparable.5.3 To determine the effect of different pressure loadings on the final thickness of TRMs, use this test method.5.4 This test method may be used for acceptance testing of commercial shipments of TRMs, but caution is advised since information on between-laboratory precision is incomplete. Comparative tests in accordance with 5.4.1 may be advisable.5.4.1 In a case of a dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and that are formed from a lot of material of the type in question. The test specimens should be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student's t-test for unpaired data and an acceptable probability level chosen by the two begun. If bias is found, either its cause must corrected, or the purchaser and be found and interpret future tests in supplier must agree to the light of the known bias.NOTE 1: The user should be aware that the compressibility of the materials, their rebound characteristics, and the like will also be affected by the thickness of the TRMs following the time when they are rolled up on rolls shipped and stored.1.1 This test method covers the resiliency or recovery of turf reinforcement mats (TRMs) after they have been subjected to three cycles of loading at 689 kPa [100 psi] for 1 min/per cycle.1.2 This test method does not provide resiliency values for TRMs under variable normal compressive stresses. This test method determines nominal resiliency.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

1.1 This specification applies to the maximum content of eight PAHs (PAH8) in materials used as synthetic turf infill.1.2 This specification outlines a test method for sample preparation and the method for analyzing the content of the eight PAHs in synthetic turf infill.1.3 This specification provides guidelines for reporting the content of the eight PAHs in the synthetic turf infill.1.4 This specification is applicable to any infill material used in synthetic turf.1.5 The values stated in SI units are to be regarded as standard. No other units are included in this standard.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

7.1 This test method is based on subsection 8.3 of Consumer Safety Specification F963, which specifies a test procedure to determine the amount of hazardous metals that have the potential to be present in toys and handled or ingested by children. Since it is possible for users of synthetic turf playing surfaces to handle or ingest particles of synthetic turf infill materials, it is necessary to determine the level of hazardous metals in the synthetic turf infill materials. The limits of hazardous metals used in this specification are based on those specified in Consumer Safety Specification F963, adjusted for statistical error correction factor as described in Consumer Safety Specification F963.AbstractThis specification covers all extractable hazardous metals (man-made or natural) that are intended for use as infill materials for synthetic turf sports surfaces. It specifies the amount of certain metals that have the potential to be extracted from synthetic turf infill materials if ingested. The time, temperature, and pH of the extraction fluid approximate the conditions the infill material would experience in the stomach during the digestive process. The levels of extractable metals are compared to maximum levels allowed in children's toys.This specification includes requirements with respect to performance (hazardous metal content), test methods, sampling, apparatus, reagents, and procedure.1.1 This specification relates to the amount of certain metals that have the potential to be extracted from synthetic turf infill materials if ingested. The time, temperature, and pH of the extraction fluid approximate the conditions the infill material would experience in the stomach during the digestive process. The levels of extractable metals are compared to maximum levels allowed in children’s toys.1.2 This specification applies to all materials (man-made or natural) that are intended for use as infill materials for synthetic turf sports surfaces.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 The dynamic interaction between the athlete and the synthetic turf surface affects the comfort and the performance of the athlete. Interaction with a surface that has low amounts of deformation and shock absorption allows the player to run fast and turn quickly, but has the potential to cause discomfort and damage to the lower extremity joints. Synthetic turf surfaces having high deformation have lower energy restitution. Less of the energy exerted by the athlete returns from the surface, possibly increasing the fatigue for the performing athlete.1.1 This test method specifies a method for measuring force reduction, vertical deformation, and energy restitution of synthetic turf surfaces.1.2 This method is used to characterize properties of synthetic turf systems including the turf fabric, infill material, and shock pad (if applicable).1.3 It can be used for characterizing synthetic turf systems in laboratory environment or in the field.1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

5.1 This test method is used to determine if the turf reinforcement mat meets specifications for mass per unit area. This test method can be used for quality control to determine specimen conformance. This measurement allows for a simple control of the delivered material by a comparison of the mass per unit area of the delivered material and the specified mass per unit area.5.2 The procedure in this test method may be used for acceptance testing of commercial shipments, but caution is advised since information about between-laboratory precision is incomplete. Comparative tests in accordance with 5.2.1 are advisable.5.2.1 In case of a dispute arising from differences in reported test results when using the procedures in this test method for acceptance testing of commercial shipments, the purchaser and the manufacturer should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. At a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and which are from a lot of material of the type in question. The test specimen should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using the appropriate Student’s t-test and an acceptable probability level chosen by the two parties before testing is begun. If a bias is found, either its cause must be found and corrected or the purchaser and the manufacturer must agree to interpret future test results in light of the known bias.1.1 This test method covers an index to the determination of mass per unit area of all turf reinforcement mats.1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 In general this test method is adapted from tests developed for woven fabrics (previously designated as Test Method D1388).4.2 The cantilever test method may not be suitable for testing products that are very limp or have a marked tendency to curl or twist at a cut edge.1.1 This test method covers the determination of the stiffness of geosynthetics used as turf reinforcement mats (TRMs).1.2 The method is applicable to TRMs of any fiber content and any number of components.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 This test method can be used to determine in-place permeability of synthetic turf playing field systems, playing field systems with pad and or premolded drainage boards, playing field systems with premolded panel base systems, porous and non porous pavement systems in order to confirm compliance with design specifications and or evaluate existing as-built conditions. The simplicity of the test method, the quickness of the procedure, and the limited requirement for special tools and apparatus’ makes this ideal for performing a large quantity of tests over a large area such as a sports field.5.2 Synthetic turf field systems tend to drain under several flow regimes. The first flow regime is surface flow where water travels across the surface from typically higher elevations to lower elevations. The second flow regime is flow through the turf surface and base system. The third flow regime is lateral flow, which has two parts. Lateral flow within the section of the turf surface and lateral flow within the pre-molded drainage board, porous pavement and or base stone system below the turf. These are depicted diagrammatically in Fig. 1.FIG. 1 Basic Flow Regime Diagram5.3 This test method can provide owners, designers and turf system builders with a clear indication of actual in-field permeability flow rates with limited effect of lateral flow through base systems and no effect from head pressure.5.4 This test method can be used to determine the effectiveness of treatments intended to reduce the effect of hydrophobicity which has been known to decrease the permeability of some synthetic turf infill materials and components.5.5 The observable performance of the test method enables one to determine permeability by both a quantitative and qualitative measure.1.1 This test method may be used to determine the permeability rate of synthetic turf playing field systems, playing field systems with pad or premolded drainage boards, or both, playing field systems with premolded panel base systems, porous and non porous pavement systems, or base stone systems in the field, or a combination thereof, by non-confined area flood test method. This system is suitable for use on the finish synthetic turf playing surface and on the stone base system below the playing system.1.2 This test method is applicable for synthetic turf playing field systems and stone bases where system is designed for permeability through the synthetic turf surface and or through a base stone surface. It is also suitable for synthetic turf playing systems that are directly underlined with resilient and nonresilient pre-molded drainage boards systems and porous pavement base systems. The method tests a larger surface area than confined ring test methods and decreases the effect lateral flow within the surface and or stone base system due to the large increase in the ratio of test surface area to the synthetic turf playing system and stone base system thickness. The method is intended to more accurately mimic natural storm flow conditions by eliminating the effect of head pressure created by the water column height which creates a pressure flow condition at the surface of the test area that does not exist naturally.1.3 This test method is intended for finish-graded and compacted stone or finished surfaces that are installed with cross-slope gradients of less than 2.0 % or under conditions where the effect of cross-slope is mitigated by high system permeability. High sloping systems tend to have high sloping base systems which may impact results due to increases in the lateral flow within the section caused increased hydraulic energy caused by larger slopes.1.4 This test method is not applicable for conditions or locations in-which surface flow, due to high surface cross-slope or proximity, carries water flow from the test site to surface and subsurface drainage trenches or structures.1.5 Further, this test method may be impacted if preformed directly after a significant rainfall event in cases where the downstream capacity of the receiving drainage system is taxed to the extent that water backs up in the downstream system.1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

5.1 Currently methods of infill sampling procedures differ from vendor to vendor and from technical agent to technical agent. Providing a uniform procedure for sampling, which allows for a consistent vertical sample, will allow for more consistent and accurate evaluation/measurement in the laboratory of samples taken in the field.5.2 The Sampling Program and associated Sample Area Site Plan (Map) shall take into account the specific purpose or purposes of the testing and determine appropriate sample areas based on needs and field conditions. A partial list of possible purposes include:5.2.1 General overall field evaluation of the infill material density, overall application rate, total quantities, and infill variation across the field area.5.2.2 Infill component composition and variation/uniformity as it relates to infill material weights and ratios. This can identify inconsistencies in construction techniques and quality control.5.2.3 Infill material evaluation for injury related surface assessment.5.2.4 Infill material end of life and potential reuse assessment.5.2.5 Field area contamination assessment.5.3 Laboratory testing that may be performed on obtained samples include but are not limited to:5.3.1 Test Method C136.5.3.2 Test Method D5644.5.3.3 Test Method F1632.1.1 This test method provides a consistent sampling procedure for obtaining infill samples of synthetic turf infill materials in the field.1.2 Operational considerations include:1.2.1 This method requires that attic stock infill materials or infill materials from areas that are out-of-play be available for refilling holes left by the sampling procedure. Replacement of infill materials shall match the composition of the material removed.1.2.2 Using this method to determine the in-situ weight and density will result in unreliable data due to the inclusion of moisture within the infill materials. Proper laboratory procedure including wet weight, dry weight before separation, and component weight after separation ensure no loss, and reliable data.1.3 Evaluation and analysis of the samples in the field and or laboratory are not covered herein.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

5.1 These test methods constitute a standard for obtaining data in research and development, quality control, acceptance and rejection under specifications, and for special purposes.5.2 The data obtained from use of these test methods are applicable to the system and its components under conditions of the particular test procedures and are not necessarily the same as the data that might be obtained in other environments or use conditions.5.3 The selection of test methods or tests should be limited to those appropriate to the system or material(s) being evaluated.1.1 These test methods establish a recommended list from which suitable test methods shall be selected for the identification of physical property characteristics and comparison of the performance properties of synthetic turf systems or components for athletic and recreational uses, or both.1.2 Some of the test procedures are suitable only for the laboratory characterization of either components or the complete system; others are suitable for tests on installed sports fields; and some tests may be applied in both the laboratory and the field.1.3 The test procedures included in these test methods apply as a group to the description of synthetic turf playing surfaces.1.4 Some of the test procedures are specific for components of the synthetic turf system, and others apply to the complete synthetic turf playing surface.1.5 Reference to the methods for testing the synthetic turf playing surface and its components contained herein should state specifically the particular test or tests desired and not necessarily refer to these test methods as a whole.1.6 This is a physical property characterization standard, and it shall not be construed as a safety standard.1.7 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

This specification details the test methods for sample preparation and analyzing, as well as guidelines for reporting the total lead content in fibers used in synthetic turf. Synthetic turf fibers shall be tested at such quantity intervals as to ensure continuing compliance with test requirements. The measured total lead content shall be within the limit specified herein.1.1 This specification applies to the maximum content of lead in fibers used in synthetic turf.1.1.1 This specification outlines a test method for sample preparation and a test method for analyzing the total lead content in synthetic turf fibers.1.1.2 This specification outlines guidelines for reporting total lead content in synthetic turf fibers.1.2 This specification applies only to synthetic turf fibers manufactured after Sept. 1, 2009.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 The compression behavior test for TRMs is intended to be an index test. It is anticipated that the results of the compression behavior test will be used to evaluate product. The results of the analyses also may be used to compare the relative compressive yield points of materials that exhibit a detectable compressive yield point. It is anticipated that this test will be used for quality control testing to evaluate uniformity and consistency within a lot or between lots where sample geometry factors, for example, thickness, or materials may have changed.NOTE 1: This is a one-dimensional test for compressive loading of a TRM in one plane.5.1.1 The compressive yield point of TRMs may be evaluated from the stress/strain relationship. Many materials exhibit compressive deformation but may not show a distinct compressive yield point.5.2 This test method can be used to evaluate the short-term stress/strain behavior of TRMs under compressive stress while loaded at a constant rate of deformation.5.3 This test method may be used for acceptance testing of commercial shipments of TRMs but caution is advised because interlaboratory testing is incomplete.5.3.1 In the case of a dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is statistical bias between their laboratories. Competent statistical assistance is recommended for the investigations of bias. As a minimum, two parties should take a group of test specimens from material shipped to project. The test specimens then should be assigned randomly in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using the Student's t-test for unpaired data and an acceptable probability level chosen by the two parties before the testing is begun. If bias is found, either its cause must be found and corrected, or the purchaser and supplier must agree to interpret future test results in the light of the known bias.1.1 This test method establishes the procedures for evaluation of the deformations of a turf reinforcement mat (TRM) under short-term compressive loading. This test method is strictly an index test method to be used to verify the compressive strength consistency of a given manufactured geosynthetic. Results from this test method should not be considered as an indication of actual or long-term performance of the TRM in field applications.1.2 Since these TRMs experience multidirectional compressive loadings in the field, this test method will not show actual field performance and should not be used for this specific objective. The evaluation of the results also should recognize that the determination of the short-term single plane compressive behavior of geosynthetics does not reflect the installed performance of TRMs and, therefore, should not be used as the only method of product or performance specification.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车