【国外标准】 Standard Test Method for Dye Penetration of Solid Fiberglass Reinforced Pultruded Stock
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
5.1 This test method is useful for establishing the integrity of composite rod. The presence of voids, cracks, and hollow fibers are considered detrimental to the structural integrity of the composite and causes reduced electrical resistance and increased current leakage.5.2 A perfect composite would be flaw-free, and there would be no possibility of wicking. Composites of this type are virtually nonexistent, as there will typically be entrapped air in the resin developed during manufacturing, occasional hollow fibers, and occasional cracks due to thermal stresses.5.3 This test method is intended to provide a tool for measuring the extent of wicking in a composite over very short lengths of material for comparative purposes. The presence of wicking over 1 in. (2.54 cm) lengths will not necessarily imply that the composite will perform unsatisfactorily for its intended end-use. Therefore, interpretation of test results shall be made carefully.5.4 This test method was developed as a technique for estimating quality and consistency of pultruded rod and bar stock, which is a composite of resin and all-roving reinforcement. This test method will be useful for a manufacturer to determine whether any gross changes in quality have taken place due to process or raw material changes as the manufacturing process also affects the quality of the product.5.5 Since the results of this test are so sensitive to sample size, penetrant type, penetrant used, viscosity, duration of test, and other factors, no attempt to arrive at or recommend development of a specification for these materials has been made. A specification shall be negotiated between supplier and end user and such specification shall be made with great care.1.1 This dye-penetrant test method covers a means of evaluating solid fiberglass all-roving reinforced pultruded rod or bar stock for longitudinal wicking. There are generally three mechanisms that promote wicking such as delaminations, longitudinal continuous voids, or the presence of hollow fibers. Any or all of them will be operating at a given time.NOTE 1: Occasionally the flaws listed above may be detected by this test, but other tests are usually required.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems has the potential to result in nonconformance with the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 10.3 and 10.6.NOTE 2: There is no known ISO equivalent to this test method.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D5117-17
标准名称:
Standard Test Method for Dye Penetration of Solid Fiberglass Reinforced Pultruded Stock
英文名称:
Standard Test Method for Dye Penetration of Solid Fiberglass Reinforced Pultruded Stock标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- 国家标准计划
- 24/30491443 DC standard
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication
- 24/30486472 DC - Product standard
- KS M ISO 4259-4 석유 및 관련 제품 — 측정 방법과 결과의 정밀도 — 제4부: 개별 실험실에서 표준 시험방법의 실행에 대한 ‘통계적 관리’ 상태를 확인하기 위한 통계적 관리도의 사용
- KS C IEC 61340-4-7 정전기학 — 제4-7부: 구체적 적용 분야에 대한 표준 시험방법 — 이온화
- KS C IEC 61340-4-8 정전기학 — 제4-8부: 구체적 적용 분야에 대한 표준 시험방법 — ESD 차폐성 — 봉투
- KS C IEC 61340-4-6 정전기학 — 제4-6부: 구체적 적용 분야에 대한 표준 시험방법 — 손목접지대
- 24/30485973 DC standard
- BS EN 14662-1:2023 - TC Tracked Changes. Ambient air quality. Standard method for measurement of benzene concentrations
- KS C IEC 61837-2 주파수 제어 및 선택을 위한 표면 실장형 압전 장치 — 표준 아웃라인 및 단자 리드 연결 — 제2부: 세라믹 함체
- BS EN IEC 61753-081-02:2023 Fibre optic interconnecting devices and passive components. Performance standard