【国外标准】 Standard Test Methods for Measuring the Reactivity of Supplementary Cementitious Materials by Isothermal Calorimetry and Bound Water Measurements
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
5.1 These test methods are used to assess the chemical (pozzolanic or hydraulic) reactivity of SCMs over a curing time of 7 days. The results of these test methods can be used to estimate the potential contribution of a SCM to the development of strength, or other properties such as lower permeability, when used with portland cement. However, the test results are not a substitute for direct measurement of the same properties of concrete made with that SCM.5.2 The calcium hydroxide, calcium carbonate, potassium sulfate, and potassium hydroxide are combined in proportions to provide a paste where the dissolved ions from these components simulate the pore solution in a portland cement system.5.3 The pastes are cured at 40 °C to accelerate the rate of reaction of slowly reactive SCMs.5.4 These test methods allow for the direct measurement of the hydraulic or pozzolanic reactivity of a potential SCM. These test methods are also suitable for screening purposes in the development and research of SCMs for use in portland cement-based systems. Furthermore, these test methods may be used in manufacturing control of portland cement-based products for assessing the hydraulic or pozzolanic reactivity of a SCM component.5.5 These test methods are based on the work by Avet et al.4 and are a result of the work of RILEM Technical Committee 267 – Tests for Reactivity of Supplementary Cementitious Materials.5 The test methods are based on established correlations between strength development and evolution of heat and binding of water for SCMs covered by Specifications C618, C989/C989M, and C1240, and by Guide C1709. For other alternative SCMs, the validity of such correlations has not been established.5.6 There is no requirement to use Method A and Method B for a given application. In many instances the choice is based on the user’s determination of available equipment. Method A can also provide an indication of rate of reactivity because measurements are taken continuously during the test period, while Method B provides the level of reactivity up to a single point in time.1.1 These two alternative test methods are used to assess the chemical reactivity of a supplementary cementitious material (SCM) as determined by measurements of cumulative heat release or bound water content of hydrated pastes composed of the SCM, calcium hydroxide, calcium carbonate, potassium sulfate, and potassium hydroxide cured at 40 °C for 3 and 7 days.1.1.1 These two test methods do not distinguish between hydraulic and pozzolanic reactivity.1.2 The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.1.3 The text of the standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.)21.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM C1897-20
标准名称:
Standard Test Methods for Measuring the Reactivity of Supplementary Cementitious Materials by Isothermal Calorimetry and Bound Water Measurements
英文名称:
Standard Test Methods for Measuring the Reactivity of Supplementary Cementitious Materials by Isothermal Calorimetry and Bound Water Measurements标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- 国家标准计划
- 24/30491443 DC standard
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication
- 24/30486472 DC - Product standard
- KS M ISO 4259-4 석유 및 관련 제품 — 측정 방법과 결과의 정밀도 — 제4부: 개별 실험실에서 표준 시험방법의 실행에 대한 ‘통계적 관리’ 상태를 확인하기 위한 통계적 관리도의 사용
- KS C IEC 61340-4-7 정전기학 — 제4-7부: 구체적 적용 분야에 대한 표준 시험방법 — 이온화
- KS C IEC 61340-4-6 정전기학 — 제4-6부: 구체적 적용 분야에 대한 표준 시험방법 — 손목접지대
- KS C IEC 61340-4-8 정전기학 — 제4-8부: 구체적 적용 분야에 대한 표준 시험방법 — ESD 차폐성 — 봉투
- 24/30485973 DC standard
- BS EN 14662-1:2023 - TC Tracked Changes. Ambient air quality. Standard method for measurement of benzene concentrations
- KS C IEC 61837-2 주파수 제어 및 선택을 위한 표면 실장형 압전 장치 — 표준 아웃라인 및 단자 리드 연결 — 제2부: 세라믹 함체
- BS EN IEC 61753-081-02:2023 Fibre optic interconnecting devices and passive components. Performance standard