
【国外标准】 IEEE/IEC Draft International Standard - Explosive atmospheres -- Part 30-1: Electrical resistance trace heating -- General and testing requirements
本网站 发布时间:
2025-04-28
- IEEE/IEC P60079-30-1
- 定价: 94元 / 折扣价: 80 元
- 在线阅读
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
This part of IEC 60079 specifies general and testing requirements for electrical resistance trace heaters for application in explosive atmospheres with the exclusion of those for Equipment Protection Level (EPL) Ga and Da. This standard covers trace heaters that comprise either factory or field (work-site) assembled units, and which may be series trace heaters, parallel trace heaters, trace heater pads, or trace heater panels that have been assembled and/or terminated in accordance with the… read more manufacturer's instructions. This standard also includes requirements for termination assemblies and control methods used with trace heating systems. The explosive atmospheres referred to in this standard are those defined in IEC 60079-10-1 and IEC 60079-10-2. Annexes D and E outline the application of this standard for those users applying the Division method of area classification. This standard supplements and modifies the general requirements of IEC 60079-0, except as indicated in Table 1. Where a requirement of this standard conflicts with a requirement of IEC 60079-0, the requirement of this standard takes precedence. read less
标准号:
IEEE/IEC P60079-30-1
标准名称:
IEEE/IEC Draft International Standard - Explosive atmospheres -- Part 30-1: Electrical resistance trace heating -- General and testing requirements
英文名称:
标准状态:
-
发布日期:
-
实施日期:
出版语种:
- 其它标准
- 上一篇: IEEE/IEC P60079-30-2 IEEE/IEC Draft International Standard for Explosive atmospheres -- Part 30-2: Electrical resistance trace heating -- Application guide for design, installation and maintenance
- 下一篇: IEEE 1017.3-2021 IEEE Recommended Practice for Specifying Electric Submersible Pump Cable--Polypropylene Insulation
- 推荐标准
- ASTM D7381-07(2021)e1 Standard Practice for Establishing Allowable Stresses for Round Timbers for Piles from Tests of Full-Size Material
- ASTM D7390-18e1 Standard Guide for Evaluating Asbestos in Dust on Surfaces by Comparison Between Two Environments
- ASTM D7510-10(2016)e1 Standard Practice for Performing Detection and Quantitation Estimation and Data Assessment Utilizing DQCALC Software, based on ASTM Practices D6091 and D6512 of Committee D19 on Water
- ASTM D7525-14(2019)e1 Standard Test Method for Oxidation Stability of Spark Ignition Fuel—Rapid Small Scale Oxidation Test (RSSOT)
- ASTM D7545-14(2019)e1 Standard Test Method for Oxidation Stability of Middle Distillate Fuels—Rapid Small Scale Oxidation Test (RSSOT)
- ASTM D7570-17(2021)e1 Standard Test Method for Evaluation of Dimensional Stability of Pile Yarn Floor Covering
- ASTM D7573-18ae1 Standard Test Method for Total Carbon and Organic Carbon in Water by High Temperature Catalytic Combustion and Infrared Detection
- ASTM D7589-16e1 Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VID Spark Ignition Engine
- ASTM D7608-18e1 Standard Test Method for Torsional Ring Shear Test to Measure Drained Fully Softened Shear Strength and Stress Dependent Strength Envelope of Fine-Grained Soils
- ASTM D7663-12(2018)e1 Standard Practice for Active Soil Gas Sampling in the Vadose Zone for Vapor Intrusion Evaluations
- ASTM D7664-10(2018)e1 Standard Test Methods for Measurement of Hydraulic Conductivity of Unsaturated Soils
- ASTM D7729-12(2018)e1 Standard Practice for Determining and Expressing Precision of Measurement Results, in the Analysis of Water, as Relative Standard Deviation, Utilizing DQCALC Software
- ASTM D7749/D7749M-11(2023)e1 Standard Test Method for Determining Integrity of Seams Produced Using Thermo-Fusion Methods for Reinforced Geomembranes by the Grab Method
- ASTM D7777-13(2018)e1 Standard Test Method for Density, Relative Density, or API Gravity of Liquid Petroleum by Portable Digital Density Meter
- ASTM D7830/D7830M-14(2021)e1 Standard Test Method for In-Place Density (Unit Weight) and Water Content of Soil Using an Electromagnetic Soil Density Gauge