
【国外标准】 Standard Test Methods for Sampling and Testing Ferroalloys for Determination of Size
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
This specification covers standard methods for sampling and testing of various ferroalloys for size analysis. Ferroalloys are classified into lump and crushed or plates sizes. The small-sized samples subject to screen testing shall be taken from the lot sample by riffling, and larger sized samples by mixing and quartering. Sizing of lumps shall be done by visual examination. Crushed or plates materials shall be subjected to sieving by using either manually driven or mechanically driven screen vibrators to divide samples into several size fractions.1.1 These test methods cover procedures for the sampling and testing of the various ferroalloys for sizing, either before or after shipment from the plants of the manufacturers.1.2 They are designed to give results representative of each lot that will be comparable with the manufacturer's certified analysis for the same lot.1.3 The purchaser may use any sampling procedure he desires, but the results obtained on such samples shall not be a basis for complaint or rejection, unless the procedure followed is of an accuracy equivalent to that prescribed in these test methods.1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4.1 Exception—The SI units that correspond to mesh sizes in Table 1 are to be regarded as standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM A610-79(2019)
标准名称:
Standard Test Methods for Sampling and Testing Ferroalloys for Determination of Size
英文名称:
Standard Test Methods for Sampling and Testing Ferroalloys for Determination of Size标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM E2601-23 Standard Practice for Radiological and Nuclear Emergency Response
- ASTM E2606-18 Standard Practice for Receipt Notification as a Result of Tangible Asset Movement
- ASTM E2607-21 Standard Practice for Cannibalization/Reclamation of Serviceable Equipment Components to Support Demand Requirements
- ASTM E2608-20 Standard Practice for Equipment Control Matrix (ECM)
- ASTM E261-16(2021) Standard Practice for Determining Neutron Fluence, Fluence Rate, and Spectra by Radioactivation Techniques
- ASTM E2611-19 Standard Test Method for Normal Incidence Determination of Porous Material Acoustical Properties Based on the Transfer Matrix Method
- ASTM E2614-15(2020)e1 Standard Guide for Evaluation of Cleanroom Disinfectants
- ASTM E2616-09(2020) Standard Guide for Remedy Selection Integrating Risk-Based Corrective Action and Non-Risk Considerations
- ASTM E2617-17 Standard Practice for Validation of Empirically Derived Multivariate Calibrations
- ASTM E2619/E2619M-17 Standard Practice for Measuring and Calculating Building Loss Features That Take Up Floor Area in Buildings
- ASTM E2624-17 Standard Practice for Torque Calibration of Testing Machines
- ASTM E2625-19 Standard Practice for Controlling Occupational Exposure to Respirable Crystalline Silica for Construction and Demolition Activities
- ASTM E2627-13(2019) Standard Practice for Determining Average Grain Size Using Electron Backscatter Diffraction (EBSD) in Fully Recrystallized Polycrystalline Materials
- ASTM E2635-22 Standard Practice for Water Conservation in Buildings Through In-Situ Water Reclamation
- ASTM E2637-17 Standard Guide for Utilizing the Environmental Cost Element Structure Presented by Classification