
【国外标准】 Standard Test Method for Evaluating Structural Adhesives for Finger Jointing Lumber
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
4.1 This test method is specifically designed to measure the performance of adhesives in finger joints manufactured under production line conditions.4.1.1 The test method can be adapted to evaluate the adhesive performance of laboratory produced finger joints using commercial finger joint cutting heads with finger joints produced following the adhesive manufacturers recommendations. The conditions under which the finger joints were produced, including any limitations, are to be reported in 9.1.2.2 (see Note 2).NOTE 2: If laboratory prepared finger joints are to be produced, record details related to adhesive used, its preparation, application to the cut finger joint, appropriate bonding parameters and limitations in the production of the finger joint assemblies.4.2 The results of the test method may be used to certify an adhesive as suitable for finger jointing lumber under production line conditions where the intended end use of the finger jointed lumber may be in a variety of bonded structural wood products.4.2.1 When the test results are to be used for certification of an adhesive a standard wood species shall be used.4.2.1.1 Standard species may be found in Table 1 of Specification D2559.1.1 This test method is designed to evaluate adhesives for finger jointing lumber used in the manufacture of a variety of bonded structural wood products such as structural glued laminated timber. It tests the tensile strength of joints under the following treatments: dry with no treatment, wet after one vacuum-pressure soak treatment, and wet after cyclic boil-dry treatment.1.2 This test method is intended neither for quality control as the test assemblies are selected for the absence of defects usually found in run-of-the-mill finger joints nor as a substitute for in-plant qualification of end joints, including full-scale joint tests.NOTE 1: This test method is specifically designed to evaluate adhesives for use in finger jointing lumber using small scale test specimens cut from carefully selected finger joint assemblies. In contrast, plant qualification and quality control require tests of full scale end joints selected randomly from production, designed to evaluate parameters beyond adhesive performance which affect the performance of the end use product.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D4688/D4688M-14(2021)e1
标准名称:
Standard Test Method for Evaluating Structural Adhesives for Finger Jointing Lumber
英文名称:
Standard Test Method for Evaluating Structural Adhesives for Finger Jointing Lumber标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM 51026-23 Standard Practice for Using the Fricke Dosimetry System
- ASTM 52303-24 Standard Guide for Absorbed-Dose Mapping in Radiation Processing Facilities
- ASTM A1-00(2018) Standard Specification for Carbon Steel Tee Rails
- ASTM A1000/A1000M-17(2023) Standard Specification for Steel Wire, Carbon and Alloy Specialty Spring Quality
- ASTM A1001-18 Standard Specification for High-Strength Steel Castings in Heavy Sections
- ASTM A1002-16(2020) Standard Specification for Castings, Nickel-Aluminum Ordered Alloy
- ASTM A1004/A1004M-99(2018) Standard Practice for Establishing Conformance to the Minimum Expected Corrosion Characteristics of Metallic, Painted-Metallic, and Nonmetallic-Coated Steel Sheet Intended for Use as Cold Formed Framing Members
- ASTM A1009-18 Standard Specification for Soft Magnetic MnZn Ferrite Core Materials for Transformer and Inductor Applications
- ASTM A101-04(2019) Standard Specification for Ferrochromium
- ASTM A1010/A1010M-13(2018) Standard Specification for Higher-Strength Martensitic Stainless Steel Plate, Sheet, and Strip
- ASTM A1012-10(2021) Standard Specification for Seamless and Welded Ferritic, Austenitic and Duplex Alloy Steel Condenser and Heat Exchanger Tubes With Integral Fins
- ASTM A1015-01(2018) Standard Guide for Videoborescoping of Tubular Products for Sanitary Applications
- ASTM A1016/A1016M-23 Standard Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel Tubes
- ASTM A102-04(2019) Standard Specification for Ferrovanadium
- ASTM A1021/A1021M-20 Standard Specification for Martensitic Stainless Steel Forgings and Forging Stock for High-Temperature Service