5.1 The use of this apparatus is intended to induce property changes associated with the end-use conditions, including the effects of the UV portion of sunlight, moisture, and heat. Exposures are not intended to simulate the deterioration caused by localized weather phenomena, such as atmospheric pollution, biological attack, and saltwater exposure.NOTE 3: Refer to Practice G151 for cautionary guidance applicable to laboratory weathering devices.5.2 Variation in results may be expected when operating conditions are varied within the accepted limits of this method.5.3 Test data for one thickness of a geomembrane cannot be used as data for other thickness geomembranes made with the same formula (polymer, pigment, and stabilizers) since the degradation is thickness related.NOTE 4: It is recommended that a similar material of known performance (a control) be exposed simultaneously with the test material to provide a standard for comparative purposes. When control material is used in the test program, it is recommended only one coupon be used for each UV exposure period to allow for OIT testing.1.1 This standard covers the specific procedures and test conditions that are applicable for exposure of unreinforced polyolefin geomembranes to fluorescent UV radiation and condensation.NOTE 1: Polyolefin geomembranes include high-density polyethylene (HDPE), linear low-density polyethylene (LLDPE), flexible polyproplyene (fPP), etc.1.2 Test specimens are exposed to fluorescent UVA-340 lamps under controlled environmental conditions. UVA-340 lamps are standard for this method.NOTE 2: Other types of fluorescent UV lamps, such as UVB-313, can also be used based upon discussion between involved parties. However, if the test is run with another type of fluorescent UV lamp, such as UVB-313, this should be considered as a deviation from the standard and clearly stated in the test report. UVB-313 and UVA-340 fluorescent lamps generate different amounts of radiant power in different wavelength ranges; thus, the photochemical effects caused by these different lamps may vary.1.3 This method covers the conditions under which the exposure is to be performed and the test methods for evaluating the effects of fluorescent UV, heat, and moisture in the form of condensation on geomembranes. General guidance is given in Practices G151 and G154.1.4 The values listed in SI units are to be regarded as the standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 This practice may be used to determine the performance, for suitable materials, in terms of any desired strength property of adhesive bonds. Test conditions of temperature and moisture only are here specified. The duration of exposure is dependent upon the nature of the adhesive and the type of specimens and will, therefore, be covered by material specifications.1.1 This practice defines conditions for determining the performance of adhesive bonds when subjected to continuous exposure at specified conditions of moisture and temperature. The performance is expressed as a percentage based on the ratio of strength retained after exposure to the original strength.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 Stem cells of hematopoietic origin are pluripotential and may be particularly sensitive to the effects of stimulation by nanoparticulate materials.5.2 The effect of particles on macrophage responses has an extensive history and can be assessed by Practice F1903. The test method described here will assess the effect on stem cells which can be progenitor cells to the macrophage line.1.1 This test method provides a protocol for quantitative analysis of the effect of nanoparticulate materials in physiologic solution (isotonic, pH 7.2 ± 0.2) on granulocyte-macrophage colony-forming units (CFU-GM).1.2 CFU-GM reflects the number of viable bone marrow cells which differentiate into granulocytes and macrophages. A decrease in CFU-GM count is indicative of a test substance’s toxicity to bone marrow and is commonly used for the identification of drug products with myelosuppressive properties, a form of immunosuppression.1.3 This test method employs murine bone marrow hematopoietic stem cells which proliferate and differentiate to form discrete cell clusters or colonies which are counted.1.4 This test method is part of the in vitro preclinical characterization cascade for nanoparticulate materials for systemic administration in medical applications.1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 702元 / 折扣价： 597 元 加购物车

3.1 Vibration encountered in the field is usually random in nature and this test can be used to determine the effects of random excitation on the membrane switch.3.2 Random vibration can cause mechanical fatigue and failure by switch components either loosening or otherwise changing over time.3.3 Experience has shown that this test will expose potential failures associated with the electronic components of a membrane switch, where tests of lower levels will not.3.4 This practice can be used to qualify a membrane switch for aerospace, medical and other applications.3.5 This test is potentially destructive, intended for device qualification.1.1 This test method establishes procedures for determining the effect of random vibration, within the specified frequency range, on switch contacts, mounting hardware, adhered component parts, solder or heat stakes, tactile devices, and cable or ribbon interconnects associated with a membrane switch or membrane switch assembly.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 0元 / 折扣价： 0 元