3.1 This test method is used to measure the surface area of precipitated, hydrated silicas that is available to the nitrogen molecule using the multipoint (B. E. T.) method. Single point nitrogen surface area is measured in accordance with the Test Methods D5604.3.2 Solids adsorb nitrogen, and under specific conditions, the adsorbed molecules approach a monomolecular layer. The quantity in this hypothetical monomolecular layer is calculated using the BET equation. Combining this with the area occupied by the nitrogen molecule yields the total surface area of the solid.3.3 This test method measures the estimated quantity of nitrogen in the monomolecular layer by adsorption at liquid nitrogen temperature and at several (at least five) partial pressures of nitrogen.3.4 Before a surface area determination can be made it is necessary that the silica be stripped of any material which may already be adsorbed on the surface. The stripping of adsorbed foreign material eliminates two potential errors. The first error is associated with the weight of the foreign material. The second error is associated with the surface area that the foreign material occupies.1.1 This test method covers a procedure which is used to measure the surface area of precipitated hydrated silicas by the conventional Brunauer, Emmett, and Teller (BET)2 theory of multilayer gas adsorption behavior using multipoint determinations, similar to that used for carbon black in Test Method D6556. This test method specifies the sample preparation and treatment, instrument calibrations, required accuracy and precision of experimental data, and calculations of the surface area results from the obtained data.1.2 This test method is used to determine the nitrogen surface area of precipitated silicas with specific surface areas in the range of 10 to 500 m2/g.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. The minimum safety equipment should include protective gloves, sturdy eye and face protection, and means to deal safely with accidental mercury spills.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 The term “surface texture” is used to describe the local deviations of a surface from an ideal shape. Surface texture usually consists of long wavelength repetitive features that occur as results of chatter, vibration, or heat treatments during the manufacture of implants. Short wavelength features superimposed on the long wavelength features of the surface, which arise from polishing or etching of the implant, are referred to as roughness.4.2 This guide provides an overview of techniques that are available for measuring the surface in terms of Cartesian coordinates and the parameters used to describe surface texture. It is important to appreciate that it is not possible to measure surface texture per se, but to derive values for parameters that can be used to describe it.1.1 This guide describes some of the more common methods that are available for measuring the topographical features of a surface and provides an overview of the parameters that are used to quantify them. Being able to reliably derive a set of parameters that describe the texture of biomaterial surfaces is a key aspect in the manufacture of safe and effective implantable medical devices that have the potential to trigger an adverse biological reaction in situ.1.2 This guide is not intended to apply to porous structures with average pore dimensions in excess of approximately 50 nm (0.05 μm).1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 590元 / 折扣价： 502 元 加购物车

1.1 This test method covers the measurement of specific surface area of carbon black exclusive of area contained in micropores too small to admit hexadecyltrimethyl ammonium bromide (cetyltrimethyl ammonium bromide, commonly referred to as CTAB). However, it should be noted that the preferred method for measuring external surface area is STSA (Test Method D 6556).1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

3.1 This test method provides a measure of the bond quality of the fibers, or particles, at the surface of wood-base fiber and particle panel materials including particleboard, medium-density fiberboard (MDF) and oriented strand board (OSB). Surface bond strength is a measure of the strength and resistance to delamination of the bond between overlay materials and panel surfaces and is an important consideration when these overlay materials, such as wood veneers, saturated papers, or plastic overlays, are to be bonded to the panel surface during secondary manufacturing.1.1 This test method is a measure of the cohesive bond strength of the fibers, or particles, on the surface of wood-base fiber and particle panels (for example, particleboard and medium-density fiberboard) in the direction perpendicular to the plane of the panel.1.1.1 To determine the internal cohesive bond strength of wood-base fiber and particle panels, use Section 11 of Test Methods D1037.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 This guide is meant to aid local and regional response teams who may use it during spill response planning and spill events.4.2 This guide should be adapted to site-specific circumstances.1.1 This guide covers the use of surface washing agents to assist in the control of oil spills. The guide is written with the goal of minimizing the environmental impacts of oil spills; this goal is the basis on which the recommendations are made. Aesthetic and socioeconomic factors are not considered although these and other factors are often important in spill response.1.2 In making surface washing agent use decisions, appropriate government authorities should be consulted as required by law.1.3 Spill responders have available several means to control or clean up spilled oil. In this guide, the use of chemical surface washing agents is considered.1.4 This guide applies only to permeable land surfaces. This guide does not apply to shorelines.1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 The purpose of this test method is to determine the shock absorption properties of a playground surface at a specific impact height in order to evaluate a particular playground surfacing system using the g-max and HIC criteria as outlined in Specification F1292. This will allow the owner/operator to specify certain minimums that they desire for their playground surface in relation to their playground equipment fall height and can be confirmed in the field after installation or throughout the functional life for the surface system utilizing Test Method F3313.5.2 This test method is to be used as a reference for specifying the impact attenuation performance of playground surfaces and the height from which they are tested.1.1 This test method covers all playground surfaces to be tested in a laboratory setting at a specific drop height established by the manufacturer of the playground surface to determine shock absorption properties at the specified height above the surface and to evaluate surfaces based on their Gmax and HIC values described in Specification F1292.NOTE 1: This test method is not intended to replace Specification F1292 for critical fall height (CFH) testing but to provide more information to either the manufacturer of the surface or the owner/operator purchasing the surface.NOTE 2: This test method informs the owner/operator of the impact attenuating performance of the surfacing system at the specified height used in the test.1.2 This test method is specific to surfacing used in conjunction with playground equipment, such as that described in Specifications F1148, F1487, F1918, and CSA Z614.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

3.1 The objective of surface treatments as documented in this practice is to improve the corrosion resistance of metallic surgical implants including, but not limited to, those manufactured from iron, cobalt, nickel, titanium, and tantalum base materials.3.2 Iron particles, ceramic media, and other foreign particles may become smeared over or embedded into the surface of implants during processing operations such as forming, machining, tumbling, media blasting, marking, and so forth. These particles should be removed to minimize localized corrosion and superficial blemishes.3.3 The various chemical and electrochemical surface treatments specified by this practice are used to remove objectionable surface contaminants and to restore maximum corrosion resistance to, or promote the creation of, an inert or passive surface, such as a metal oxide film, as is applicable to the specific material. Some of these treatments are referred to as passivation treatments. The preferred surface treatment for a given application varies depending on the implant material and the nature of the surface contaminants.3.4 Depending on the implant, its material, and the type of marking method and procedure, the marking may be applied before or after a chemical or electrochemical surface treatment. When marking is performed after the surface treatment, the localized implant surface shall be evaluated to determine if there is a need for additional surface treatment.NOTE 1: The need for additional surface treatment is likely for stainless steel with all marking methods, and for nonferrous alloys when the marking method involves direct or second-hand contact with iron-based or other material that would be considered an objectionable surface contaminant.3.5 The selection of procedures to be applied to the implants, and additional requirements which are not covered by this practice, may be included in the implant production specification.1.1 This practice provides descriptions of surface characteristics, surface preparation, and marking for metallic surgical implants, with the purpose of improving the corrosion resistance of the implant surfaces and markings.1.2 Marking nomenclature and neutralization of endotoxin are not specified in this practice (see X1.4).1.3 Surface requirements and marking methods included in the implant specification shall take precedence over requirements listed in this practice, where appropriate.1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 This guide is meant to aid local and regional response teams who may use it during spill response planning and spill events.4.2 This guide should be adapted to site-specific circumstances.1.1 This guide covers the use of surface washing agents to assist in the cleanup of oil spills. This guide is written with the goal of minimizing the environmental impacts of oil spills; this goal is the basis on which the recommendations are made. Aesthetic and socioeconomic factors are not considered although these and other factors are often important in spill response.1.2 In making surface washing agent use decisions, appropriate government authorities should be consulted as required by law.1.3 Spill responders have available several means to control or clean up spilled oil. In this guide, the use of chemical surface washing agents is considered.1.4 This is a general guide only. Oil, as used in this guide, includes crude oils and refined petroleum products. Differences between individual surface washing agents or between different oil products are not considered.1.5 This guide applies only to impermeable surfaces. This guide does not apply to shorelines.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers the requirements for zinc coatings applied by the electrolytic process to any grade of hot-rolled or cold-rolled steel sheets for applications requiring designation of the coating mass on each surface. Coating application shall be done on one or both surfaces with equal or differential coating masses and similar levels of corrosion protection, and shall have no effect on the base metal mechanical properties. The coated sheets may be available as commercial steel (CS), drawing steel (DS), deep drawing steel (DDS), extra-deep drawing steel (EDDS), structural steel (SS), high-strength low-alloy steel (HSLAS), high-strength low-alloy steel with improved formability (HSLAS-F), solution-hardened steel (SHS), or bake-hardenable steel (BHS). Coatings shall be designated accordingly, and shall undergo test methods such as weigh-strip-weigh method, nondestructive X-ray fluorescence measurement, and Coulometric method. Accordingly, individual coating designations should conform to coating weight, mass per surface, and thickness requirements.1.1 This specification covers zinc coatings applied by the electrolytic process to hot-rolled and cold-rolled steel sheet. The coating has a smooth, spangle-free surface. The zinc-coated sheet covered in this specification is produced in a wide range of coating masses to provide coatings that are compatible with the anticipated service life required. The coating mass varies, from very thin coatings that are usually painted to provide good service, to relatively heavy masses that provide good corrosion resistance in the bare (unpainted) condition.1.2 The product shall be coated on one or both surfaces with equal or differential coating masses on the two surfaces. Sheet coated with equal coating masses on each surface has similar levels of corrosion protection on each surface. Often, however, a higher level of corrosion protection is required on one surface than is required on the other. Thus, one surface is specified to have a heavier coating mass than the other. Either surface, when specified to be painted, will provide additional corrosion protection as compared to an unpainted surface.1.3 This coating process has essentially no effect on the base metal mechanical properties and use is permitted on any grade of hot- or cold-rolled steel sheet. The coated sheet is available as Commercial Steel (CS), Drawing Steel (DS), Deep Drawing Steel (DDS), Extra-Deep Drawing Steel (EDDS), Structural Steel (SS), High-Strength Low-Alloy Steel (HSLAS), High-Strength Low-Alloy Steel with Improved Formability (HSLAS-F), Solution-Hardened Steel (SHS), Bake-Hardenable Steel (BHS), Required Hardness Steel (RHS), or Special Forming Steel (SFS); see Specifications A1008/A1008M and A1011/A1011M.1.4 Ordered dimensions are specified based on the finished coated steel sheet product and all dimensional tolerances are defined per Specification A568/A568M, Section 8.1.5 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 Both sellers and purchasers of alumina and quartz will find the test method useful to determine the specific surface area and indirectly as a measure of the particle size for material specifications, manufacturing control, and research and development.1.1 This test method covers the determination of the specific surface area of aluminas and silicas used in the manufacture of ceramics. The test method is a general one, permitting the use of any modern commercial nitrogen adsorption apparatus but strictly defining the outgassing procedure. Calculations are based on the Brunauer-Emmett-Teller (BET) equation.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 This practice provides minimum recommendations for the installation of thick poured lightweight cellular concrete floor underlayments suitable to receive resilient floor coverings. This practice establishes the proper preparation, installation and quality control for thick poured lightweight cellular concrete floor underlayments.4.2 Actual requirements for thick poured lightweight cellular concrete underlayments are generally included as part of project plans or specifications and may vary from the recommendations set forth in this practice. Project plans or specifications, or both, shall supersede the recommendations set forth in this practice.1.1 This practice covers the installation and preparation of the thick poured lightweight cellular concrete underlayments over wood structural panel subfloors in commercial structures or over concrete floors in commercial structures and the preparation of the thick poured lightweight cellular concrete underlayment surface prior to the installation of resilient flooring in commercial buildings.1.2 This practice points out the factors that are required to be controlled while installing thick poured lightweight cellular concrete underlayment as a base for resilient flooring.1.3 This practice does not cover the structural adequacy of the wood structural panel subfloor or concrete subfloor. The structural integrity of assemblies is governed by local building codes.1.4 This practice does not supercede the thick poured lightweight cellular concrete underlayment manufacturers', adhesive manufacturers' or resilient flooring manufacturers' written instructions. Consult the individual manufacturer for specific recommendations.1.5 Thick poured lightweight cellular concrete underlayments are not suitable for use on concrete slabs on ground due to potential moisture problems arising from moisture intrusion, unless an adequate vapor retarder or vapor barrier is present directly beneath the concrete subfloor.1.6 The values stated in inch-pound units are to be regarded as standard. The values stated in parentheses are mathematical conversions to SI Units, which are provided for information only.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

3.1 Vapor retarders used on thermal insulation can be exposed to liquid water in normal usage. Some cannot tolerate such exposure without suffering damage. Others are designed to withstand intermittent or occasional exposure in their intended indoor usage. Still others are intended for outdoor applications and exposure to the elements. (not covered by this standard).3.2 This test is used to evaluate products or materials that are used where exposure to liquid water on the surfaces on an intermittent or occasional basis is possible. Such products would be expected to absorb very little water, if any, in this test.3.3 In the test, the specimen is exposed to a specified volume of water over a given exposure area, with a resultant head pressure.3.4 The amount of water absorbed by a specimen is measured in this test. This is used to characterize the water resistance of the specimen. The less water absorbed, the more water resistant the surface is considered to be.1.1 This test method details a procedure for the determination of the surface water resistance of a vapor retarder by measurement of the quantity of water absorbed in a specified time by the service-exposed surface of a vapor retarder intended for use on thermal insulation.1.2 This test method covers vapor retarders that are expected to withstand intermittent or occasional exposure to liquid water on the exposed side. Examples of this exposure are condensation and light rain during installation before a structure is enclosed.1.3 This method does not cover vapor retarders intended for exposure to the elements in outdoor applications.1.4 This method does not cover thermal insulation products that also act as vapor retarders, such as elastomeric foam and cellular glass.1.5 In the test, the specimen is exposed to a specified volume of water over a given exposure area, with a resultant head pressure.1.6 The test method is based on Test Method D3285 (withdrawn), the so-called “Cobb” test used for paper.1.7 The values stated in SI units are to be regarded as standard.1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 The procedures described herein are recommended for evaluating the corrosion or marine fouling behavior, or both, of materials exposed to quiescent or local tidal flow conditions, or both.4.1.1 This practice is not intended to cover the influence of high seawater velocity or the behavior of materials in seawater which has been transported from its source.4.1.2 Some aspects of this practice may be applicable to testing in tanks and troughs, which are continuously provided with surface seawater pumped directly from the source. Additionally, some aspects may also be applicable to deep ocean testing.NOTE 1: Guide G78 provides guidance for conducting crevice corrosion tests under controlled seawater test conditions.4.2 While the duration of testing may be dictated by the test objectives, exposures of more than six months or one year are commonly used to minimize the effects of environmental variables associated with seasonal changes or geographic location, or both. Refer also to 7.3 for test duration recommendations.4.3 The procedures described are applicable for the exposure of simple test panels, welded test panels, or those configured to assess the effects of crevices, or both, such as those described in Guide G78. In addition, they are useful for testing of actual components and fabricated assemblies.4.4 It is prudent to include control materials with known resistance to seawater corrosion or fouling, or both, as described in Test Method D3623.NOTE 2: Materials which have been included in ASTM Worldwide Seawater Corrosivity Studies include UNS K01501 (carbon steel), UNS C70600 (90/10 CuNi) and UNS A95086 (5086-H116 Al).2, 4NOTE 3: In the case of evaluations of aluminum alloys, care should be exercised in the location of specimens near copper or high copper-containing alloys. In some instances, it is not sufficient to simply electrically isolate specimens to prevent bi-metallic (galvanic) corrosion; copper ions from nearby corroding copper or copper-base alloys can deposit on aluminum and accelerate its corrosion.1.1 This practice covers conditions for the exposure of metals, alloys, and other materials in natural surface seawater such as those typically found in bays, harbors, channels, and so forth,2 as contrasted with deep ocean testing.3 This practice covers full immersion, tidal zone and related splash, and spray zone exposures.2, 41.2 This practice sets forth general procedures that should be followed in conducting seawater exposure tests so that meaningful comparisons may be made from one location to another.1.3 This practice identifies recommended procedures for evaluating the effects of natural surface seawater on the materials exposed.1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 The surface area of zinc-oxide in rubber can significantly affect cure activation and vulcanizate properties.4.2 The specific surface area of zinc-oxide is usually measured by nitrogen absorption which requires the use of equipment not normally found in rubber laboratories. This test method allows a ranking of zinc-oxide samples according to their surface areas with respect to a known standard using a simplified procedure involving mixing of rubber compounds and measuring cure times with oscillating disk or rotorless cure meters.4.3 This test method may be used for quality control, research and development work, and comparison of different zinc-oxide samples.1.1 This test method specifies the standard materials, mixing procedure, and test method for ranking zinc-oxide samples according to their specific surface area in a standard test formula based on chloroprene rubber (CR).1.2 The ranking is based on the cure time of the standard CR formulation.1.3 The accurate surface area cannot be determined by this test method, since factors other than surface area may influence the cure times to some extent (for example acidity, heavy metal traces, etc.).1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers drawn seamless aluminum-alloy tube of specified tensile properties for use in surface condensers, evaporators, and heat exchangers. The tube shall be produced by drawing an extruded tube made from hollow extrusion ingot (cast in hollow form or pierced) and extruded by use of the die and mandrel method. The tube shall be subjected to tension, leak, and expansion tests.1.1 This specification2 covers aluminum-alloy (Note 1) drawn seamless round tube in straight lengths designated as shown in Table 2, for use in surface condensers, evaporators, and heat exchangers.NOTE 1: Throughout this specification use of the term alloy in the general sense includes aluminum as well as aluminum alloy.NOTE 2: For drawn seamless tubes used in general applications, see Specifications B210 and B210M; for extruded tubes see Specifications B221 and B221M; for seamless pipe and seamless extruded tube used in pressure applications see Specification B241/B241M; and for structural pipe and tube see Specification B429/B429M.(A) Limits are in percent maximum unless shown as a range or otherwise stated.(B) Analysis shall be made for the elements for which limits are shown in this table.(C) For purposes of determining conformance to these limits, an observed value or a calculated value attained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the specified limit, in accordance with the rounding-off method of Practice E29.(D) Others includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in this specification. However, such analysis is not required and may not cover all metallic Others elements. Should any analysis by the producer or the purchaser establish that an Others element exceeds the limit of Each or that the aggregate of several Others elements exceeds the limit of Total, the material shall be considered nonconforming.(E) Other Elements—Total shall be the sum of unspecified metallic elements 0.010 % or more, rounded to the second decimal before determining the sum.(F) Vanadium 0.05 max.(G) The aluminum content shall be calculated by subtracting from 100.00 % the sum of all the metallic elements present in amounts of 0.010 % or more, rounded to the second decimal before determining the sum.(H) Composition of cladding alloy as applied during the course of manufacture. The sample from finished tube shall not be required to conform to these limits.(I) In case there is a discrepancy in the values listed in Table 1 with those listed in the “International Alloy Designations and Chemical Composition Limits for Wrought Aluminum and Wrought Aluminum Alloys” (known as the “Teal Sheets”), the composition limits registered with the Aluminum Association and published in the “Teal Sheets” shall be considered the controlling composition. The “Teal Sheets” are available at http://www.aluminum.org/tealsheets.(A) To determine conformance to this specification, each value for ultimate strength and for yield strength shall be rounded to the nearest 0.1 ksi and each value for elongation to the nearest 0.5 %, both in accordance with the rounding-off method of Practice E29.(B) The basis for establishment of mechanical property limits is shown in Annex A1.(C) Elongation of full-section and cut-out sheet-type specimens is measured in 2 in., of cut-out round specimens, in 4 × specimen diameter.1.2 Alloy and temper designations are in accordance with ANSI H35.1/H35.1(M). The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A91060 for aluminum 1060, in accordance with Practice E527.1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.1.4 This specification is the inch-pound companion to Specification B234M; therefore, no SI equivalents are presented in the specification.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车