定价： 590元 / 折扣价： 502 元 加购物车

定价： 590元 / 折扣价： 502 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers counter-top model noncarbonated beverage dispensers that are mechanically refrigerated and have rigid, transparent, impact-resistant containers to afford a visual display of the beverage dispensed. The beverage dispensers covered by this specification are intended to circulate, cool, and dispense noncarbonated beverages such as pulpy juices, frozen concentrates, and syrup drinks. The beverage dispensers shall be of the following types, classes, styles, and sizes: Types I and II; Classes A and B; Styles A (sizes 1, 2, 3, and 4), B (sizes 1 and 2), and C (size 1). The beverage dispenser shall consist essentially of a base that contains a complete refrigeration system and supports a rigid, transparent, impact resistant, bowl-type beverage container(s) with cover(s). Performance test, pull-down test, energy consumption test, maximum ambient temperature and high humidity test, bowl impact test, and operation production performance test shall be performed to conform with the specified requirements.1.1 This specification covers counter-top model noncarbonated beverage dispensers that are mechanically refrigerated and have rigid, transparent, impact-resistant containers to afford a visual display of the beverage dispensed. The beverage dispensers covered by this specification are intended to circulate, cool, and dispense noncarbonated beverages such as pulpy juices, frozen concentrates, and syrup drinks.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 The following safety hazard caveat pertains only to the test method portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers commercial bulk milk dispensers for dispensing milk in commercial and institutional food service establishments. These specified commercial bulk milk dispensers are self-contained, manually-operated, gravity-fed, mechanically refrigerated cabinets with lift-up valves used for dispensing refrigerated milks and milk fluid products. Commercial bulk milk dispensers covered in this specification are classified by type, electrical class and size. In this specification, types 1, 1A, 2A, 3A, 4A are determined and covered. For electrical classes of bulk milk dispenser, the classes 1 and 2 are described. Sizes 1 to 3 of milk dispenser are used in this specification to describe commercial bulk milk dispenser. The physical properties of commercial bulk milk dispenser are also covered in this specification wherein the design and manufacturer, the cooling system, the controls, the standards and compliance and the accessories are specified in accordance with agreed requirements and specifications. Sampling, testing, and quality assurance of finished units are also covered in this specification wherein these tests and procedures must be met in accordance with ANSI/UL 471 and NSF/ANSI 20.1.1 This specification covers commercial bulk milk dispensers which are for dispensing milk in the commercial and institutional food service establishments. These commercial bulk milk dispensers are self-contained, manually-operated, gravity-fed, mechanically refrigerated cabinet(s) with lift-up or push-type valves. These units are intended to dispense refrigerated milk and fluid milk products.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers the performance requirements and corresponding test procedures for self-contained shipboard dehumidifiers that use hermetic refrigerant motor-compressors. The components of the dehumidifier, including the motor-compressor, condensing unit, dehumidifying coil, air-circulating fan, and accessories, shall all be enclosed within a metal cabinet. Dehumidifiers shall be evaluated by design capacity test, overload test, inclination test, and corrosion resistance test, and should operate satisfactorily as specified. Requirements for design documentation, schematic drawings, and manufacturer's manual are also considered.1.1 This specification covers self-contained dehumidifiers using hermetic refrigerant motor-compressors.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 The following safety hazards caveat pertains only to the test methods portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers the requirements for coating of cadmium mechanically deposited on metal products. Cadmium coatings shall classified on the basis of thickness, as follows: Class 12; Class 8; and Class 5. Cadmium coatings shall be identified as Type I and Type II on the basis of supplementary treatment required. The coating shall be uniform in appearance and free of blisters, pits, nodules, flaking, and other defects that can adversely affect the function of the coating. All steel parts that have ultimate tensile strength and that contains tensile stresses caused by machining, grinding, straightening, or cold-forming operation shall be given a stress relief heat treatment prior to cleaning and metal deposition. The minimum hours to failure (appearance of white corrosion products and red rust for mechanically deposited cadmium coatings on iron and steel) of Type I and Type II coatings shall be indicated to guarantee satisfactory performance. The test specimen shall undergo adhesion, corrosion resistance, and appearance tests. The thickness of the coating shall be determined by the microscopical method, or the magnetic method, or the beta backscatter method, as applicable.1.1 This specification covers the requirements for a coating of cadmium mechanically deposited on metal products. The coating is provided in various thicknesses up to and including 12 μm.1.2 Mechanical deposition greatly reduces the risk of hydrogen embrittlement and is suitable for coating bores and recesses in many parts that cannot be conveniently electroplated (see Appendix X3).1.3 Cadmium coatings are usually applied to provide engineering properties and corrosion resistance. The performance of a cadmium coating depends largely on its thickness and the kind of environment to which it is exposed. Without proof of satisfactory correlation, accelerated tests such as the salt spray (fog) test cannot be relied upon to predict performance in other environments, nor will these serve as comparative measures of the corrosion resistance afforded by coatings of different metals. Thus, although there is a marked superiority of cadmium coatings over zinc coatings of equal thickness in the salt spray test, this is often not the case under conditions of use, so that further testing in the service environment should be conducted.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see 1.5 and 1.6.1.5 Warning—Cadmium is toxic and must not be used in a coating for articles that can come into contact with food or beverages, or for dental or other equipment that can be inserted into the mouth. Consult appropriate agencies for regulations in this connection.1.6 Warning—Because of the toxicity of cadmium vapors and cadmium oxide fumes, cadmium-coated articles must not be used at temperatures of 320 °C and above. They must not be welded, spot-welded, soldered, or otherwise strongly heated without adequate ventilation that will efficiently remove all toxic fumes.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers the requirements for zinc coatings that are mechanically deposited on iron or steel basis metals. The zinc coatings are classified according to thickness and identified into two types; as coated without supplementary treatments or with colored chromate conversion treatment. The thickest coating classes are usually referred to as "mechanically galvanized". All deposited coatings should have a bright uniform silvery appearance, and a matte to medium-bright luster. Samples should be tested for adhesion, salt-spray corrosion resistance, appearance, thickness, and absence of hydrogen embrittlement. All tests results should comply with the given requirements.1.1 This specification covers the requirements for a coating of zinc mechanically deposited on iron and steel basis metals. The coating is provided in several thicknesses up to and including 107 μm. The seven thickest classes are usually referred to as “mechanically galvanized.”1.2 Units—The values stated in SI units are to be regarded as the standard. The inch-pound equivalents of SI units are given for informational purposes.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: The performance of this coating complies with the requirements of Specification A153/A153M and MIL-C-81562.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

5.1 This test method is for measuring the mechanically tapped packing density of powders that are smaller than 0.8 mm in diameter, such as Fluidized Catalytic Cracking Catalysts (FCC).1.1 This test method covers the determination of the mechanically tapped packing density of fine catalyst and catalyst carrier particles smaller than 0.8 mm in diameter.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

1.1 This specification addresses mechanically attached polymeric roof underlayment used in steep slope roofing.1.2 The objective of this specification is to provide a finished product that will be used as a water-shedding underlayment layer on steep sloped roofs prior to and after installation of the primary roof covering.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

This practice covers the minimum requirements for the installation of mechanically attached poly(vinyl chloride) sheet roofing. The procedure includes the setting up of mechanical affixments using bar or strip anchoring systems, or plate or disc anchoring systems, and the hot air welding of lap areas. Delivery, storage, and handling of materials, environmental conditions, and substrate preparation have been dealt with as well.1.1 This practice covers the minimum requirements for the installation of mechanically attached poly(vinyl chloride) roofing.1.2 For the purpose of this application practice, the structure and deck are assumed to be mechanically sound, able to accept the weight of the membrane and other roofing system materials, comply with local building codes, and other roofing requirements. The insulation layer(s) and vapor retarder, if specified, are assumed to be in place, secured, and acceptable for use with the membrane.1.3 This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7.

定价： 0元 / 折扣价： 0 元