This specification covers batch-type electric vegetable peeling machines of the following style: Style 1, Size A, and Style 2, Size A, Size B, and Size C. The cylinder or hopper shall be sheet aluminum or stainless steel, or cast iron. Machines intended for marine applications shall be furnished with a stainless steel cylinder. The inside surface of all cylinders shall be covered by silicon carbide or aluminum oxide. The disk shall be cast aluminum, formed stainless steel, or reinforced plastic. The cylinder covering ring shall be cast aluminum, spun sheet aluminum, or fiberglass-reinforced plastic. The supporting base of the flour mounted Style 2 machine shall be steel, aluminum, or stainless steel. The vegetable peeler shall comply to the specified physical requirements specified for the following: (1) cylinder or hopper, (2) disk, (3) vegetable outlet, (4) peel trap, (5) waste outlet, (6) water inlet and sprayer, (7) cylinder covering ring, (8) Style 1, counter mounted, (9) Style 2, floor mounted, (10) waste disposer, (11) electrical devices such as motors, wiring, timer, and switch, and (12) piping, tubing, fittings, and valves. The peeler shall meet the hazard protection requirements including switch guard and shall conform to the performance requirements which shall be tested by operational test.1.1 This specification covers batch-type vegetable peeling machines.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 The following safety hazards caveat pertains only to the test methods portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 加购物车

定价： 590元 加购物车

定价： 590元 加购物车

定价： 571元 加购物车

定价： 702元 加购物车

定价： 712元 加购物车

定价： 712元 加购物车

This specification covers the standard for martensitic stainless steel for various structural, architectural, pressure vessel, and heat-resisting applications. The material shall undergo heat-treatment by tempering. The steel shall conform to the requirements as to chemical composition specified for carbon, manganese, phosphorus, sulfur, silicon, chromium, nickel, molybdenum, and nitrogen. Mechanical testing shall be performed on the steel and shall conform to the specified values in mechanical properties such as yield strength, tensile strength, elongation, and Brinell hardness.1.1 This specification covers martensitic stainless steels for various structural, architectural, pressure vessel, and heat-resisting applications. The mechanical properties of these steels are customarily, but not necessarily, developed by a suitable heat treatment generally referred to as tempering.1.2 Steel products under this specification are available in two grades:Grade Yield Strength, min, ksi [MPa]40 [275] 40 [275]50 [345] 50 [345]1.3 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements; however, current practice normally limits the maximum thickness of plates furnished under this specification to 2 in. [50 mm].1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

This specification covers single-reduced black plate produced from low carbon, cold-reduced steel, furnished in coils and cut sizes, for use in the manufacture of containers, closures, signs, toys and other products, as well as for plating applications. The black plates shall be produced with ground roll and shot-blasted roll finishes and shall be furnished oiled or dry.1.1 This specification covers single-reduced black plate produced from low carbon, cold-reduced steel, furnished in coils and cut sizes, for use in the manufacture of containers, closures, signs, toys and other products, as well as for plating applications.1.2 It may be supplied dry or oiled and with or without surface treatment. This product is normally supplied with a trimmed edge.1.3 This specification is applicable to orders in either inch-pound units (as A625), which is supplied in thicknesses from 135-lb base weight (0.0149 in.) and lighter, or SI units (as A625M), which is supplied in thicknesses from 0.378 mm and lighter.1.4 The values stated in either inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

定价： 646元 加购物车

定价： 712元 加购物车

定价： 571元 加购物车

定价： 646元 加购物车

定价： 571元 加购物车

定价： 515元 加购物车