This specification deals with consumer safety for clothing storage chests. It is intended to minimize the incidents and injuries to children resulting from normal use and reasonably foreseeable misuse or abuse of these chests. The design of the lid support, closures, and locks shall conform to their performance requirements. Test methods shall be done for lid support mechanisms and closures. Finishes and materials used in the construction of the chests shall be nonhazardous. All paints and coatings shall comply with the limitations of antimony, arsenic, barium, cadmium, chromium, lead, mercury, and selenium.1.1 This consumer safety specification covers the performance requirements and test methods to ensure the safety of chests.1.2 This consumer safety specification is intended to minimize the incidents and injuries to children resulting from normal use and reasonably foreseeable misuse or abuse of these chests.1.3 This consumer safety specification applies to products commonly known as cedar chests, hope chests, blanket chests, and keepsake chests, or other similar closed rigid boxes designed and marketed as sealed storage containers for clothes, blankets, linens, keepsake or other household items. Products subject to these requirements are:1.3.1 Those with a single volume of 1.1 ft3 (0.031 m3) or more measured with all removable shelves or compartments removed from the product, and1.3.2 Those intended to create a tightly sealed storage space when the lid is closed for purposes such as the prevention of insect infestation and dust or dirt contamination.1.4 No chest produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.6 The following precautionary caveat pertains only to the test methods portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 This classification identifies sources of PE film. The separation by sources also improves the usefulness of the material. Sources are post-consumer PE films from shrink wrap, dry cleaning film, merchandise bags, grocery sacks, stretch wrap, recycle bags, redemption bags, bubble packaging film, commercial/industrial liners/bags, and commercial overwrap.4.2 This classification is useful in characterizing post-consumer film to be used as a feedstock for recycling.4.3 It is neither the intent nor the purpose of this classification to specify the suitability of the recycled material for specific applications.1.1 This document provides for the classification of post-consumer polyethylene (PE) film derived from specific sources. It also identifies characteristics useful in determining the acceptability of the film for recycling into molding and extrusion materials. It is neither the intent nor the purpose of this classification to specify the suitability of the recycled material for specific applications.1.2 This classification provides that the source of the material be listed as an aid in identification. The separation by source also improves the usefulness of the material. Sources are post-consumer PE films from shrink wrap, dry cleaning film, merchandise bags, grocery sacks, stretch wrap, recycle bags, redemption bags, bubble packaging film, and commercial/industrial liners/bags and overwrap. Other post-consumer PE films shall be added to this classification when such material streams are defined.1.3 It is not the function of this classification to provide data for specific product design or process-performance purposes.1.4 The supplier shall provide a written certification with each shipment stating that the material is derived from post-consumer PE film sources described within this classification.1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.NOTE 1: There is no known ISO equivalent to this standard.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

1.1 This consumer safety specification covers establishment of performance requirements, test methods, and labeling requirements to minimize the hazards to users of scooters as identified in the introduction.1.2 This specification is intended to cover use of this product for children ages 5 years and older.1.3 No scooter produced after the approval date of this specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements herein.1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this consumer safety specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 This test method is a way to evaluate the effects of contaminant particles found in HDPE products containing PCR-HDPE, primarily corrugated pipe. Particles of significant number, size and shape can reduce the slow crack growth resistance of the products. This test is performed in water without a controlled defect such as a notch. Since there is no notch, it is not necessary to use a surfactant in the water bath. It is a constant load test.4.2 This test may be used to evaluate various blends of recycled and virgin materials. For example, a material with high stress crack resistance and few contaminants can be blended with materials that are less resistant to cracking to enhance the overall stress crack resistance of the blend.4.3 The test can be conducted at various temperature and stress conditions. If at least three (3) different temperature/stress conditions are evaluated, an estimate of the service lifetime of the material can be predicted with the use of bi-directional shifting or the rate process method.4.4 The test can also be performed under a single applied load and a single temperature to create a single point test useful for comparative purposes as well as for quality control.1.1 This test method covers an un-notched constant ligament stress (UCLS) test for use with HDPE materials that contain post-consumer recycled HDPE (PCR-HDPE). Contaminants in the PCR-HDPE can initiate stress cracks at elevated temperatures, and this test method evaluates the response of these materials to a constant applied stress.1.2 The test method is focused on HDPE corrugated pipe containing PCR-HDPE, but can be used in other applications where PCR-HDPE is used.1.3 The test utilizes the same devices used to perform the NCTL test (Test Method D5397) and the NCLS test (Test Method F2136), but the test is conducted with different specimens and with the use of water instead of a surfactant solution. The test specimen is larger than standard NCLS and NCTL specimens to increase the number of contaminant particles in the specimen that might grow cracks.1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification is intended for consumer safety and establishes performance requirements, test methods, and marking requirements to promote safe use of bedside sleepers. It explains the test methods that are conducted on all bedside sleepers, namely the product disengagement test method, the product disengagement rationale, and the folding latch test method.1.1 This consumer safety specification establishes performance requirements, test methods, and marking requirements to promote safe use of bedside sleepers.1.2 This consumer safety specification is intended to minimize the risk of injury to an infant from the normal use and reasonably foreseeable misuse of a bedside sleeper.1.3 This consumer safety performance specification covers products intended to provide sleeping space for an infant up to approximately 5 months of age (or when child begins to push up on hands and knees). These products are intended to be secured to the side of an adult bed for the purpose of having a baby sleep in close proximity to an adult.1.4 No bedside sleeper produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with the specification unless it complies with all of the requirements contained herein.1.5 This consumer safety performance specification is not intended to address incidents and injuries resulting from alteration or unreasonable abuse or misuse of the product by a child or child care provider.1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.7 The following precautionary caveat pertains only to the test method portion, Section 6 of this consumer safety performance specification. This standard may involve the use of hazardous materials, operations and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This consumer safety specification establishes performance requirements, test methods and marking requirements to promote safe use of sling carriers. It indicates the performance requirements and test methods of sling carriers; these tests are the static load test, dynamic load test, adhesion test, occupant retention test, and restraint system. This specification also identifies the proper markings and labels that should be placed on the sling carriers.1.1 This consumer safety specification establishes performance requirements, test methods and marking requirements to promote safe use of sling carriers.1.2 This consumer safety specification is intended to minimize the risk of injury to an occupant from the normal use and reasonably foreseeable misuse of products.1.3 For purposes of definition, a sling carrier is a product of fabric or sewn fabric construction, which is designed to contain up to two (2) children in an upright or reclined position while being supported by the caregiver’s torso. Sling carriers are normally used from full-term birth to 35 lb (15.9 kg) unless the manufacturer indicates that a higher weight limit is allowed.NOTE 1: Slings consist of a variety of unstructured designs ranging from a hammock-shaped product suspended on the caregiver’s upper torso to a long length of material wrapped around the caregiver’s body.1.4 The sling carrier is normally “worn” by the caregiver, and thus the child is supported from one or both shoulders of the caregiver. These products are worn on the front, hip or back of the caregiver, with the child either facing towards or away from the caregiver or reclined on the front only of the caregiver.1.5 No sling carrier produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with the specification unless it complies with all of the requirements contained herein.1.6 This consumer safety specification is not intended to address incidents and injuries resulting from the interaction of other persons or objects with the caregiver and child while the sling carrier is in use.1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.8 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This practice identifies the method of presenting information on selected performance and physical characteristics of a vacuum cleaner. Information will be presented to consumers in the form of a buyer's guide, with cleaner characteristics as follows: brand, model number, weight of cleaner, bag capacity, maximum cleaning distance from outlet, cleaning ability, embedded dirt, maneuverability, maximum air power, quietness, and durability.1.1 This practice identifies the method of presenting information on selected performance and physical characteristics of a residential vacuum cleaner.1.2 This information is intended to assist the consumer in comparing selected characteristics of vacuum cleaner models.1.3 It is also intended that this information be presented in a manner that is meaningful and understandable to the consumer.1.4 The characteristics are selected from those for which ASTM test methods have been developed.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

1.1 This consumer safety specification establishes testing requirements for structural integrity and performance requirements for children’s chairs and stools. It also provides requirements for labeling. The standard does not apply to products used in a commercial setting or to products that do not have a rigid frame such as bean bag chairs or foam chairs. This standard does not apply to seats with restraint systems, infant or infant/toddler rockers, children’s step stools, or children’s potty chairs. The term unit or product will refer to a child’s chair or stool.1.2 This specification covers a chair or stool intended to be used by a single child who can get in and get out of the product unassisted and with a seat height 15 in. or less, with or without a rocking base.1.3 No product produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all applicable requirements contained herein, before and after all testing.1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

This specification establishes requirements and test methods for specified elements and certain mechanical hazards in children's jewelry. It also includes recommendations for age labelling and warnings, as well as guidelines on identifying the primary intended users, namely children or adults. The specification also lists the lead content limits for children's jewelry, the materials that are excluded from the lead limits in children's jewelry, and the approved materials for children's body piercing jewelry.1.1 This specification establishes requirements and test methods for specified elements and certain mechanical hazards in children’s jewelry. It also includes recommendations for age labeling and warnings, and guidelines on identifying the primary intended users (children or adults). It does not purport to cover every conceivable hazard of children’s jewelry. It does not cover product performance or quality, except as related to safety. This specification has no requirements for those aspects of children’s jewelry that present an inherent and recognized hazard as part of the function of jewelry, such as small parts. This specification establishes requirements recognizing that not all jewelry is appropriate for all age groups. Jewelry is not recommended for young children 3 and under absent close parental supervision.1.2 This specification applies only to jewelry, as defined in 3.2.1, which is designed or intended primarily for children 12 years of age and younger, as defined in 3.2.2. Children’s jewelry is a product principally designed and intended as an ornament worn by a child. This includes a product or a component of the product intended to be removed and worn by a child as an item of ornamentation (that is, a shoe charm that can be placed on a bracelet). Adult jewelry, which is defined as jewelry designed and intended for use primarily by those over age 12, is covered by another ASTM standard, Consumer Safety Specification F2999.1.3 This specification does not apply to the following:1.3.1 Toy jewelry or any other products that are intended for use by a child when the child plays (that is, a necklace worn by a doll or stuffed animal; novelty jewelry with play value);21.3.2 Accessories (that is, Handbags, Belts);1.3.3 Apparel (except as described in 3.2.1(p));1.3.4 Footwear (except as described in 3.2.1(p));1.3.5 Any other item whose primary purpose is functional (that is, keys, key chains, or other items not primarily intended to be worn as a personal item of ornamentation).1.4 This consumer safety specification includes the following sections:Title Section 1Referenced Documents 2Definitions 3Age-Labeling 4Specifications for Lead in Children’s Jewelry 5Specifications for Children’s Body-Piercing Jewelry 7Specifications for Antimony, Arsenic, Barium,Cadmium, Chromium, Mercury andSelenium in Paint and Surface Coatingsof Children’s Jewelry 8Specifications for Cadmium in Substrate Materialsof Children’s Jewelry 9Specification for Nickel in Metal Componentsof Children’s Jewelry 10Specification for Phthalates in Plasticized Components of Children’s Jewelry 11Specifications for Liquid-Filled Children’s Jewelry 12Mechanical Requirements for Children’s Jewelry 13Test Methods 14Keywords 15Annex Annex A1Rationales Appendix X11.5 The following precautionary statement pertains only to the test methods portion of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

1.1 This provisional consumer safety specification covers establishment of performance requirements, test methods, and labeling requirements to minimize the hazards to users of scooters as identified in the introduction.1.2 This specification is intended to cover use of this product for children ages 5 years and older.1.3 No scooter produced after the approval date of this specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements herein.1.4 The values stated in inch-pound units are to be regarded as the standard. SI values, if given in parentheses, are for information only.1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this consumer safety specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

定价： 0元 / 折扣价： 0 元

1.1 This consumer safety specification establishes safety performance requirements, test methods, and labeling requirements to minimize the hazards to children presented by diaper changing tables as identified in the introduction.1.2 This specification is intended to apply to diaper changing tables for commercial use. It is intended for use with children up to 3.5 years of age and weighing less than 50 lbs.1.3 No diaper changing table produced after the approval date of this consumer safety performance specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements herein.1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this consumer safety specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

1.1 This consumer safety specification establishes minimum requirements for the design and performance of bunk beds. It also contains requirements for labeling and instructional material.1.2 This consumer safety specification is intended to minimize accidents to children resulting from normal use and reasonably foreseeable misuse or abuse of bunk beds. This consumer safety specification is written within the current state of the art of bunk bed technology and does not address bunk beds that are blatantly misused or are used in a careless manner that disregards warning statements and safety instructions provided with each bunk bed.1.3 For the purpose of this consumer safety specification, a bunk bed (hereinafter referred to as a bed) is defined as any structure that includes at least one sleeping surface in which the underside of any of its foundations is over 30 in. (762 mm) from the floor.1.4 This consumer safety specification does not address bunk beds for institutional use (for example, in prisons, military facilities, dormitories, and so forth).1.5 The values stated in inch-pound units, as well as any specified ISO/ANSI standard hardware, are to be regarded as the standard. The values given in parentheses are for information only.1.6 The following safety hazards caveat pertains only to the test methods portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This consumer safety specification addresses incidents associated with corded baby monitors that were identified by the U.S. Consumer Product Safety Commission (CPSC), including strangulations as a result of entanglement in cords. It establishes requirements for corded baby monitors, including audio monitors, video monitors, and motion sensor monitors. It also provides requirements for labeling, instructional material and packaging, and is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of baby monitors. This specification also addresses calibration and standardization, general requirements, test methods, product marking and labeling, and instructional literature.1.1 This consumer safety specification establishes requirements for corded baby monitors, including audio monitors, video monitors, and motion sensor monitors. It also provides requirements for labeling, instructional material and packaging.1.1.1 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of baby monitors.1.2 No product produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all applicable requirements contained herein, before and after all testing.1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

1.1 This consumer safety performance specification covers performance requirements, test methods and marking requirements to promote safe use of a stationary activity center by an occupant. 1.2 This consumer safety performance specification is intended to minimize the risk of incidents to an occupant resulting from normal use and reasonably foreseeable misuse or abuse of a stationary activity center. 1.3 No stationary activity center produced after the approval date of this consumer safety performance specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein. 1.4 This consumer safety performance specification is not intended to address incidents and injuries resulting from the interaction of other persons with the child occupant in the stationary activity center or the incidents resulting from abuse and misuse by children able to walk. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 The following precautionary caveat pertains only to the test methods portion, Section 7, of this consumer safety performance specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

This consumer safety specification establishes design requirements, testing requirements and methods, and requirements for labeling for full-size and non-full-size crib mattresses. Crib mattress produced after the approval date of this specification shall be deemed non-compliant unless it conforms to all requirements described by the specification. The standard covers calibration and standardization, test methods, and marking and labeling.1.1 This consumer safety specification establishes design requirements, testing requirements and methods, and requirements for labeling for full-size crib mattresses, non-full-size crib mattresses, and after-market mattresses for play yards and non-full size cribs.1.2 No crib mattress produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.1.3 Units—The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车