定价： 481元 / 折扣价： 409 元 加购物车

This specification covers the properties and tests for bituminous membrane water vapor retarders used in contact with soil or granular fill under concrete slabs. Tests may be conducted on both new materials and materials that have been conditioned or exposed to simulate service conditions. The water vapor retarders shall consist of asphaltic materials reinforced with multiple plies of suitable fabric, and shall meet the following property requirements when tested: water vapor permeance; tensile strength; puncture resistance; and thickness. When specifically required by the buyer for use in special conditions, the retarders shall additionally adhere to properties such as resistance to plastic flow and elevated temperatures, effect of low temperature on bending, resistance to deterioration from petroleum vehicle for soil poisons, and resistance to deterioration from exposure to ultraviolet light.1.1 This specification covers bituminous water vapor retarders for use in contact or granular fill under concrete slabs.1.2 The specified tests are conducted on new materials and materials that have been conditioned or exposed to simulate potential service conditions.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers high calcium, dolomitic and magnesian-hydrated lime for use in asphalt cement or bituminous pavements. Hydrated lime, either dry or slurry form, shall conform to the chemical composition requirements for calcium and magnesium oxides, carbon dioxide, unhydrated calcium and magnesium oxides, and free moisture of dry hydrates as shall be determined by chemical analysis. The particle size of hydrated lime shall also be determined using a standardized spray nozzle and pressure gauge.1.1 This specification covers high calcium, dolomitic and magnesian-hydrated lime for use in asphalt cement or bituminous paving mixtures.NOTE 1: Hydrated lime, either calcitic, dolomitic, or magnesian, improves bonding of bitumen and aggregates which reduces susceptibility to moisture damage, reduces age hardening by chemically stabilizing polar compounds found in asphalts, and increases initial stiffness of asphalt mixtures.NOTE 2: No attempt is made to present requirements for any by-product lime.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 Bituminous geomembranes, whether made from oxidized or polymer-modified bitumen, may contain a significant amount of mineral stabilizer. The amount of mineral stabilizer used in a bituminous geomembrane has an effect on several physical properties, including but not limited to cold temperature, flexibility, and asphalt penetration (see Guide D6455 for a list of PBGM properites).1.1 This test method covers the procedure for the determination of mineral stabilizer content in prefabricated bituminous geomembranes (PBGMs) by calcination.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 618元 / 折扣价： 526 元 加购物车

4.1 This method is used to evaluate the tensile properties of BGMs. It can be used for manufacturing quality control or acceptance testing.4.2 This test method uses a dumbbell specimen. The shape and dimensions of the specimen are defined in this standard. No other shape or dimensions are allowed. Other mechanical properties of BGMs may be measured using different test methods. Refer to Guide D6455.4.3 The reported properties are the maximum strength and elongation at maximum strength.1.1 This test method is used to measure the tensile properties of bituminous geomembranes (BGMs) using a dumbbell-shaped specimen.1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers two types of factory prepared reinforced bituminous flashing sheets used for roofing and waterproofing systems. The bitumen used may be asphalt, coal-tar pitch, or polymer modified bitumen. The reinforcement may include any one or a combination of organic (wood fiber), polyester, or glass fiber felts, woven fabrics, or thermoplastic films. Fine mineral powders, granules, or metal foils may be used as surfacing. Specimens shall be sampled, be tested for, and consequently conform to dimensional and physical properties, as follows: mass; thickness; load-strain properties; impact resistance; tear strength and resistance; flexibility; breaking load; and elongation at break. Calculation procedures for the mean, estimated standard deviation, and mean variance of test values from specimens tested before and after heat conditioning are also detailed.1.1 This specification covers factory-prepared reinforced bituminous sheet used in flashing. The bitumen used may be asphalt, coal-tar pitch, or polymer-modified bitumen. The reinforcement may include any one or a combination of organic (wood fiber), polyester, or glass fiber felts, woven fabrics, or thermoplastic films. Fine mineral powders, granules, or metal foils may be used as surfacing.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.1.3 The following precautionary statement pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers hot-mixed, hot-laid asphalt, tar, emulsified asphalt, and recycled bituminous paving mixtures for base, binder, leveling, and surface courses. The aggregates, mineral fillers, bitumen (asphalt cement, tar cement, or emulsified asphalt as appropriate), and bituminous paving mixtures shall be in accordance to specified consistency and compositions. Products shall be sampled, and undergo sieve analysis and other forms of test methods as appropriate for extracting bitumen content, specific gravity, plasticity index, percentage of coated particles, recovery of extracted asphalt, penetration of recovery asphalt, air voids, and absolute viscosity.1.1 This specification covers hot-mixed, hot-laid asphalt, tar, emulsified asphalt, and recycled bituminous paving mixtures for base, binder, leveling, and surface courses.1.2 The values stated in SI units are to be regarded as the standard. Combining values from the two systems may result in nonconformance with the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

This specification covers prefabricated modified bituminous sheet materials with polyester fabric reinforcement, with or without granules, that use atactic polypropylene (APP) as the primary modifier and are intended for use in the fabrication of multiple ply roofing and waterproofing membranes. This specification is not intended for (1) issues regarding the suitability of specific roof constructions or application techniques and (2) in-place roof system design criteria such as fire resistance, field strength, impact/puncture resistance, material compatibility, uplift resistance, the need for field applied coatings, and others. Type I and II modified bituminous sheet materials reinforced with polyester fabric, with granule surfacing (Grade G) and smooth surfacing (Grade S) are covered by this specification The APP modified bituminous coating shall be permitted to be compounded with a mineral stabilizer. To prevent sticking in the roll, the reverse side and any selvage shall be permitted to be covered with a fine mineral surfacing or any other surfacing that will not interfere with adhesion or bonding of the lap. The sheet shall conform to the minimum physical properties prescribed for: peak load, elongation, ultimate elongation, tear strength, low temperature flexibility, dimensional stability, compound stability, granule embedment, water absorption, moisture content, and low temperature unrolling. The finished product shall conform to the requirements prescribed for net mass and dimensions such as width of roll, area of roll, selvage width, thickness, and bottom side coating thickness. The specified ultimate elongation, high temperature stability, and low temperature unrolling test methods shall be used.1.1 This specification covers prefabricated modified bituminous sheet materials reinforced with polyester fabric, with or without granules, that use atactic polypropylene (APP) as the primary modifier and are intended for use in the fabrication of multiple ply roofing and waterproofing membranes.NOTE 1: Many modified bituminous sheets are currently marketed with polyester mat reinforced with glass yarns to improve processing in the manufacture of the finished modified bitumen product and to reduce distortions that may be introduced during production. These glass yarns are typically a small percentage of the reinforcement and do not contribute to the physical properties of the finished product so much as to make these products be classified by Specification D6223/D6223M.1.2 This specification is intended as a material specification only. Issues regarding the suitability of specific roof constructions or application techniques are beyond the scope of this specification.1.3 The specified tests and property limits used to characterize the sheet materials covered by this specification are intended to establish minimum properties. In-place roof system design criteria such as fire resistance, field strength, impact/puncture resistance, material compatibility, uplift resistance, the need for field applied coatings, and others, are factors beyond the scope of this material specification.1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.5 The following precautionary statement pertains only to the test method portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers Grades G (granule surfaced) and S (smooth surfaced) prefabricated bituminous sheet materials reinforced with a combination of polyester fabric and glass fiber, and modified with atactic polypropylene (APP), intended for use in the fabrication of multiple ply roofing and waterproofing membranes. This specification is intended as a material specification only, and does not address issues regarding the suitability of specific roof constructions or application techniques. The specified tests and property limits used to characterize the sheet materials covered by this specification are intended to establish minimum properties. Also, in-place roof system design criteria such as fire resistance, field strength, impact/puncture resistance, material compatibility, uplift resistance, the need for field applied coatings, and others are factors beyond the scope of this material specification. The physical properties for which sheet materials shall be tested on and consequently conform to are peak load before and after heat conditioning, elongation at peak load, tear strength, low temperature flexibility, dimensional stability, compound stability, granule embedment, water absorption, moisture content, and low temperature unrolling.1.1 This specification covers prefabricated modified bituminous sheet materials reinforced with a combination of polyester fabric and glass fiber, with or without granules, that use atactic polypropylene (APP) as the primary modifier and are intended for use in the fabrication of multiple ply roofing and waterproofing membranes.1.2 This specification is intended as a material specification only. Issues regarding the suitability of specific roof constructions or application techniques are beyond the scope of this specification.1.3 The specified tests and property limits used to characterize the sheet materials covered by this specification are intended to establish minimum properties. In-place roof system design criteria such as fire resistance, field strength, impact/puncture resistance, material compatibility, uplift resistance, the need for field applied coatings, and others, are factors beyond the scope of this material specification.1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers prefabricated modified bituminous sheet materials with glass fiber reinforcement, which use atactic polypropylene (APP) as the primary modifier and which are intended for use as a base sheet in the fabrication of multiple ply roofing and waterproofing membranes. The high temperature stability and low temperature unrolling shall be tested to meet the requirements prescribed.1.1 This specification covers prefabricated modified bituminous sheet materials with glass fiber reinforcement, which use atactic polypropylene (APP) as the primary modifier and which are intended for use as a base sheet in the fabrication of multiple ply roofing and waterproofing membranes.1.2 This is a material specification only. Issues regarding the suitability of specific roof constructions or application techniques are beyond the scope of this specification.1.3 The specified tests and property limits used to characterize the sheet materials covered by this specification are intended to establish minimum properties. In-place roof system design criteria, such as fire resistance, field strength, impact/puncture resistance, material compatibility, uplift resistance, the need for field applied coatings, and others, are factors beyond the scope of this material specification.1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.5 The following precautionary statement pertains only to the test method portion, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

3.1 These tests are useful in sampling and testing solvent bearing bituminous compounds to establish uniformity of shipments.1.1 These test methods cover procedures for sampling and testing solvent bearing bituminous compounds for use in roofing and waterproofing.1.2 The test methods appear in the following order:  SectionSampling 4Uniformity 5Weight per gallon 6Nonvolatile content 7Solubility 8Ash content 9Water content 10Consistency 11Behavior at 60°C [140°F] 12Pliability at –0°C [32°F] 13Aluminum content 14Reflectance of aluminum roof coatings 15Strength of laps of rolled roofing adhered with roof adhesive 16Adhesion to damp, wet, or underwater surfaces 17Mineral stabilizers and bitumen 18Mineral matter 19Volatile organic content 201.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 This guide outlines general procedures for the storage and application of various prefabricated sheets made using modified bituminous materials and intended for use as below-grade and below-wearing-surface waterproofing.4.2 The substrate used for applications described in this guide shall be concrete or masonry.4.3 This application consists of a prefabricated reinforced modified bituminous sheet applied to a suitable substrate using a bituminous-based, cold-applied adhesive or mastic. Application rates given are typical for such installations.4.4 This guide is intended to supplement instructions from designers and manufacturers.1.1 This guide lists application and installation requirements for fully adhered, cold-applied, prefabricated modified bituminous membrane waterproofing systems for below-grade or below-wearing-surface (such as plaza decks) vertical or horizontal applications.1.2 For the purposes of this application guide, the substrate is assumed to be structurally sound, sloped to drain (if new construction), and meeting the local building code requirements. Similarly, the system components are assumed to comply with all federal, state, and local requirements in effect at the time of installation.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.4 This guide may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

1.1 This test method covers procedures for preparing and testing laboratory-fabricated or field-recovered cores of bituminous mixtures to determine resilient modulus values using the repeated-load indirect tension test. The procedure described covers a range of temperatures, loads, loading frequencies, and load durations. The recommended test series consists of testing at 41, 77 (Note 1), and 104°F (5, 25 (Note 1), and 40°C) at one or more loading frequencies, for example, at 0.33, 0.5, and 1.0 Hz for each temperature. This recommended series will result in nine test values for one specimen which can be used to evaluate the overall resilient behavior of the mixture. Note 1-Ambient laboratory temperature may be substituted as appropriate. 1.2 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

1.1 This practice covers the preparation of beams of bituminous paving mixtures by means of a mechanical compactor that imparts a kneading action compacting the beam by a series of individual impressions made with a ram.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

4.1 This practice for preparation of test panels greatly increases the likelihood of achieving reproducible results in subsequent testing.1.1 This practice covers a procedure for the preparation of accelerated and outdoor weathering test panels of bituminous coatings. It is considered suitable for the preparation of film thicknesses in the range from 0.25 to 2.54 mm [0.010 to 0.100 in.].1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (Warning—Mercury has been designated by EPA and many state agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury-containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA's website, http://www.epa.gov/mercury/faq.htm, for additional information. Users should be aware that selling mercury or mercury-containing products, or both, in your state may be prohibited by state law.)1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车