【国外标准】 Standard Guide for Design and Construction of Coal Ash Structural Fills
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
4.1 General: 4.1.1 Many CCPs are suitable materials for the construction of engineered structural fills. CCPs may be used as: structural fill for building sites and foundations; embankments for highways and railroads, road bases, dikes, and levees; and in any other application requiring a compacted fill material. Their low unit weight, relatively high shear strength, ease of handling, and compaction make CCPs useful as fill material. However, the specific engineering and environmental properties of these materials can vary from source to source and must be evaluated for each material, or combination of materials, to be used for an engineered structural fill. Information contained in Guide D5759 may be applicable to some CCPs to be used in engineered structural fills. AASHTO Standard Practice PP059-09-UL also addresses the use of coal combustion fly ash in embankments. The requirements for the type of CCPs that can be used for specific engineered structural fills may also vary because of local site conditions or the intended use of the fill, or both. Environmental considerations are addressed in Section 5.4.1.2 CCPs can be a cost-effective fill material. In many areas, they are available in bulk quantities at a reasonable cost. The use of CCPs conserves other resources and reduces the expenditures required for the purchase, permitting, and operation of a soil borrow pit. CCPs often can be delivered to a job site at near optimum moisture content and generally do not require additional crushing, screening, or processing as compared to comparable native materials.4.1.3 Use of CCPs conserves natural resources by avoiding extraction or mining of soils, aggregates, or similar fill material that also conserves energy and reduces greenhouse gas emissions.4.1.4 The volume of beneficially used CCPs preserves valuable landfill space.4.2 Regulatory Framework: 4.2.1 Federal—Currently, there are no federal regulations addressing the beneficial use of CCPs. States and local jurisdictions have oversight of CCP management and beneficial use activities within their states4.2.2 State and Local Jurisdictions—Laws and regulations regarding the use of CCPs vary by state and local jurisdictions. It is incumbent upon the project owner and designer to determine any local or state guidance, policies, or regulations pertaining to the use of CCPs.1.1 This guide covers procedures for the design and construction of engineered structural fills using coal combustion products (CCPs) including but not limited to fly ash, bottom ash, boiler slag or other CCPs that can meet the requirements of an engineered fill as described herein. CCPs may be used alone or blended with soils or other suitable materials to achieve desired geotechnical properties.1.2 This guide describes the unique design and construction considerations that may apply to engineered structural fills constructed of with CCPs that have been adequately characterized as being suitable for this beneficial use.1.3 Beneficial utilization of CCPs consistent with this standard conserves land, natural resources, and1.4 This guide applies only to CCPs produced primarily by the combustion of coal.1.5 The testing, engineering, and construction practices for coal ash fills are similar to generally accepted practices for natural soil fills. Coal ash structural fills should be designed using generally accepted engineering practices. However, when CCPs are used in saturated conditions such as ponds or impoundments, the potential for liquefaction may need to be considered.1.6 Laws and regulations governing the use of coal ash vary by state. The user of this guide has the responsibility to determine and comply with applicable requirements.1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM E2277-14(2019)
标准名称:
Standard Guide for Design and Construction of Coal Ash Structural Fills
英文名称:
Standard Guide for Design and Construction of Coal Ash Structural Fills标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 其它标准
- 上一篇: ASTM E2276-10(2019) Standard Test Method for Determining the Bacteria-Eliminating Effectiveness of Hygienic Handwash and Handrub Agents Using the Fingerpads of Adults
- 下一篇: ASTM E2278-13(2019) Standard Guide for Use of Coal Combustion Products (CCPs) for Surface Mine Reclamation: Revegetation and Mitigation of Acid Mine Drainage
- 推荐标准
- 国家标准计划
- 24/30491443 DC standard
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication
- 24/30486472 DC - Product standard
- KS M ISO 4259-4 석유 및 관련 제품 — 측정 방법과 결과의 정밀도 — 제4부: 개별 실험실에서 표준 시험방법의 실행에 대한 ‘통계적 관리’ 상태를 확인하기 위한 통계적 관리도의 사용
- KS C IEC 61340-4-7 정전기학 — 제4-7부: 구체적 적용 분야에 대한 표준 시험방법 — 이온화
- KS C IEC 61340-4-6 정전기학 — 제4-6부: 구체적 적용 분야에 대한 표준 시험방법 — 손목접지대
- KS C IEC 61340-4-8 정전기학 — 제4-8부: 구체적 적용 분야에 대한 표준 시험방법 — ESD 차폐성 — 봉투
- 24/30485973 DC standard
- BS EN 14662-1:2023 - TC Tracked Changes. Ambient air quality. Standard method for measurement of benzene concentrations
- KS C IEC 61837-2 주파수 제어 및 선택을 위한 표면 실장형 압전 장치 — 표준 아웃라인 및 단자 리드 연결 — 제2부: 세라믹 함체
- BS EN IEC 61753-081-02:2023 Fibre optic interconnecting devices and passive components. Performance standard