【国外标准】 Standard Practice for Data Recording Procedure for Welding Devices Used to Produce Thermal Fusion Welds in Geomembrane Systems
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
4.1 Standard wedge welding devices rely on the operator to properly adjust the welding parameters (temperature, speed, and pressure) which are needed to create a sound weld. Changes in one or more of these parameters during production seaming, whether deliberate or accidental, can lead to poor weld quality. Prior to data acquisition systems, verifying welding parameters throughout the welding process relied solely on periodic visual observations and documentation, leaving substantial room for error. This ASTM standard practice, which requires a data acquisition system to be installed on thermal fusion welding devices, allows for the recording of these welding parameters along the entire length of the welded seam at pre-determined intervals, throughout the entire thermal fusion seaming process.4.2 The acquired data can be used in the construction quality control / construction quality assurance program to compare the welding parameters at recorded locations along the welded length to preset values, such as the values obtained during the trial seam, to facilitate detection of anomalies anywhere on the welded length.4.3 This practice does not cover the precision of the measurement, that is, the accuracy of the recorded values of temperature, speed, pressure, or position on the site. It is limited to the data acquisition process.4.4 Data acquisition parameters, such as the frequency at which the data are recorded, may be adjusted by the user depending on project specifications.1.1 This practice establishes the minimum required data recording, saving, and reporting requirements for data acquisition devices used in thermal fusion welding of geomembrane systems. Thermal fusion welding devices may include hot-wedge or hot-air wedge welders. From the data collected using this practice, it is possible to compare the welding parameters used on any production weld to those obtained during the trial welding and to the set welding parameters. This practice does not purport to identify the quality of any given weld. This standard can be used for all geomembranes, homogeneous or scrim reinforced, that can be seamed by thermal fusion welding methods.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D8468-23
标准名称:
Standard Practice for Data Recording Procedure for Welding Devices Used to Produce Thermal Fusion Welds in Geomembrane Systems
英文名称:
Standard Practice for Data Recording Procedure for Welding Devices Used to Produce Thermal Fusion Welds in Geomembrane Systems标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 其它标准
- 推荐标准
- 国家标准计划
- 24/30491443 DC standard
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication
- 24/30486472 DC - Product standard
- KS M ISO 4259-4 석유 및 관련 제품 — 측정 방법과 결과의 정밀도 — 제4부: 개별 실험실에서 표준 시험방법의 실행에 대한 ‘통계적 관리’ 상태를 확인하기 위한 통계적 관리도의 사용
- KS C IEC 61340-4-7 정전기학 — 제4-7부: 구체적 적용 분야에 대한 표준 시험방법 — 이온화
- KS C IEC 61340-4-6 정전기학 — 제4-6부: 구체적 적용 분야에 대한 표준 시험방법 — 손목접지대
- KS C IEC 61340-4-8 정전기학 — 제4-8부: 구체적 적용 분야에 대한 표준 시험방법 — ESD 차폐성 — 봉투
- 24/30485973 DC standard
- BS EN 14662-1:2023 - TC Tracked Changes. Ambient air quality. Standard method for measurement of benzene concentrations
- KS C IEC 61837-2 주파수 제어 및 선택을 위한 표면 실장형 압전 장치 — 표준 아웃라인 및 단자 리드 연결 — 제2부: 세라믹 함체
- BS EN IEC 61753-081-02:2023 Fibre optic interconnecting devices and passive components. Performance standard